Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This professional mixer of optimum performance and reliability is the result of selection of choice electronic components and severe quality control. The information and instructions contained in this manual are necessary to ensure safe operation of your equipment and to maintain it in good working condition. NOTE: The specifications mentioned hereafter apply to all standard models as of serial numbers SX-S 16150, and SX-V 120022. SONOSAX reserves the right to modify these characteristics at any time without prior notice. TABLE OF CONTENTS 1. PREPARATION OPERATING INSTRUCTIONS INPUT MODULE after serial nb 16579 STANDARD INPUT MODULE Differences from the newer Power / Mute modules MASTER MODULE SX-S EXTENSION MODULE file://D:\Z_Library\Webcopy\sonosax\SXS\sxsume.html 26.08.2004 SONOSAX SX/S USER MANUAL Seite 2 von 22 INSTALLATION INSTRUCTIONS for SX022270 SX-S Extension Module FOUR CHANNEL MATRIX MODULE ADDITIONAL AUX MODULE INPUT MONITORING MODULE(SX-V only) BALANCED TRANSFORMER OUTPUT MODULE SONOSAX SX-V TIPS ON USING YOUR MIXER 1. PREPARATION 1.1 Opening the cover Release the 2 slide-locks and simultaneously slide out the cover. 1.2 Closing the cover Replace the cover and slide all the way in until the locks catch. 1.3 Removing the battery compartment Make sure that the handle is in rest position. Remove the battery pack by releasing the 2 slide-locks, tilting the compartment diagonally towards you and lifting it out over the handle. IMPORTANT: Keep the slide-locks pressed towards the center untill the battery compartment is completely lifted out of the mixer. 1.4 Opening the battery compartment The battery compartment may now be opened by loosening the screw on the left. Remove the plastic side cover. Insert: • 8 alkaline D-cells or 8 rechargeable nickel-cadmium batteries for the SX-S6 • 10 alkaline D-cells or 10 rechargeable nickel-cadmium batteries for the SX-8 or SX-S10. NOTE:On the left of the battery compartment, you will find the hex wrench (2mm) which will enable you to completely disassemble the SX-S without using any other tool. WARNING :Never leave discharged batteries in your SX-S. Make sure before charging that your SX-S only contains rechargeable NiCd batteries. To ensure optimal autonomy, use only professional alkaline D-cells. Also check the manufacture date of D-cells. file://D:\Z_Library\Webcopy\sonosax\SXS\sxsume.html 26.08.2004 SONOSAX SX/S USER MANUAL Seite 3 von 22 1.5 Closing the battery compartment Replace the plastic side cover. NOTE : Certain D-Cells are longer than standard D-Cell batteries and slight difficulty may be found in closing the compartment if such batteries are used. Your nearest SONOSAX agent or the manufacturer in Switzerland can provide assistance should a problem arise due to this difference in length. Replace the battery compartment while holding in the slide-locks and making sure the power contacts are correctly positioned. The battery compartment is in place when the slide-locks return easily to their original position. 1.6 External power supply (also refer to 2.2 and 2.3) SONOSAX SX-S mixers can be powered from a 9-15V DC (SX-S6) or 11-15 DC (SX-S8/10) power supply capable of delivering at least 1.5A. Average power consumption is approximately 500mA. The DC power supply input connector (LEMO, Type FGJ IB 303CLLD62, SONOSAX Part nb. 860202) is located on the rear panel of the SONOSAX mixer. Pin No.3 is allocated to the NiCd batteries charge current. Nominal current is 400mA and nominal charging time is 15 hours. WARNING : DO NOT ATTEMPT TO CHARGE D-CELL BATTERIES. 1.7 Power supply block diagram 1.8 Fuses Your SONOSAX SX-S is protected against overloads and reversed polarity by two T2.5A fuses located : INSIDE THE BATTERY COMPARTMENT (ON THE RIGHT). To replace the fuse,remove the cover on the right of the battery compartment with the hex wrench.NOTE : Here you will find spare T2.5A fuses. • ON THE EXTERNAL DC PC BOARD. Located below the two faders of the master module. To gain access to this fuse, remove the bottom of the SX-S mixer with the hex wrench. RETURN TO TABLE OF CONTENTS 2. OPERATING INSTRUCTIONS 2.1 Switching on the SONOSAX mixer Using D-cells or NiCd batteries: Depress POWER push-button on the master module. The two control LEDs of the modulometer should light up within 3 seconds. If they do not light up: • Check that batteries have been inserted correctly inside the battery compartment. file://D:\Z_Library\Webcopy\sonosax\SXS\sxsume.html 26.08.2004 SONOSAX SX/S USER MANUAL Seite 4 von 22 • If necessary change the batteries. Using the Sonosax external power supply: IMPORTANT : Before turning on the unit, make sure the voltage selector is correctly positioned at either 110V or 220V depending on local current supply. If needed, change selector position by using a screwdriver, a ball point pen or similar instrument. At 110V, the mixer may be powered from 100 to 125V , 50 to 60 Hertz; at 220V, from 200 to 260V, 50 to 60 Hertz. Newer SX-S Mixers use an a...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - Professional Portable Mixing Console SONOSAX SX-S (179.26 kb)