l Always set the guitar’s VOLUME control and the volume control on the amplifier to their minimum levels when connecting or disconnecting the cable. l The built-in preamplifier is automatically turned ON when a guitar cable is connected to the output jack. When not using the instrument, or when playing it without amplification, be sure to remove the guitar cable from the output jack so that the preamplifier power is turned OFF. Also, if the instrument is not going to be used for an extended period of time, or when battery power is depleted, we recommend that the batteries be removed in order to avoid power consumption or leakage. l Even when the guitar cable is disconnected from the output jack, power is turned ON when the TUNER switch is ON ( ). Always turn the TUNER switch OFF ( ) after using the tuner. NOMENCLATURE/CONTROL INSTRUCTIONS Battery Holder Control Section Output Jack (with power switch function) Pickup Section q VOL Control: Controls the volume. * Always set the volume to its minimum level when connecting or disconnecting the cable. w 3-Band Equalizer: Adjusts the LOW, MID, and HIGH frequency levels. e TUNER Switch: Switches the tuner ON/OFF. r Display: Displays tuner information and settings, and A. F. R. functions. t TYPE Switch: Selects the pickup’s mic simulation type (1: large diaphragm condenser mic/ 2: small diaphragm condenser mic/ 3: ribbon mic). y FOCUS/WIDE Switch: Selects the setting for the simulated mic. FOCUS ( ): This setting delivers a clear tone appropriate for use when playing with a band. WIDE ( ): This setting delivers broad tone appropriate for solo use. u RESONANCE Control: Rotating to the right delivers more body tone, rotating to the left produces less. The knob’s central detent position is the standard setting. i BLEND Control: Controls the mix level of signals received from the pickup and the simulated mic. Rotate fully to the left for 100% pickup signal and fully to the right for 100% simulated mic signal. o A.F.R. Switch: When feedback occurs, this function automatically detects the problem frequency and applies a filter to eliminate the feedback. Sound Hole Cover (supplied): Inserting the sound hole cover into the sound hole effectively reduces feedback. SPECIFICATIONS l Syste m: System-63 l Pickup: Ba r Sensor (Piezo t ype) l Prea m pl ifier Con trol s: Vol., 3 -Band EQ (HIGH, MID, LOW ), T YPE (1/2 /3), FOCUS/ WIDE, RESONANCE, BLEND, A .F.R., TUNER l Ou tp ut Jack: Combination e nd pin/p owe r switch l Ou tp ut Impe da nce: 1k . l Bat te ri es: Size A A alkaline bat ter y (LR6) x 2 l Ba t te r y Life: Approx. 20 hours ( Without tuner and using alkaline bat teries. May dif fe r due to ope r ating conditions.) l Tu ner: Chromatic t ype (12 semi-tone s), Calibration (A= 438 to 445Hz), Ac curacy range +/– 3 ce nts l Acce s so ri es: Neck adjustment hex-wrench x1, Size A A alka line bat ter y x 2, Sound hole cover x1 As battery power becomes depleted, the triangular icons blink alternately ( ) in the display, replace the batteries as soon as possible. q Press the release in the direction inlever on the battery case dicated by the arrow Battery Holder Alkaline battery x2 in the illustration in order to unlock it, and then slide out the battery holder. w Remove the old batteries from the battery holder, and insert the two new size AA alkaline batteries. Make sure that the poles on the batteries are properly positioned as shown in the diagram inside of the holder. * Use alkaline batteries only. * Always change both batteries at the same Release Lever time. Do not mix new and old batteries, or different type batteries (batteries made by different manufacturers or batteries by the same manufacturer but of different types). Not doing so can result in fire, etc. * Never dismantle the batteries and never dispose batteries in fire. * Never touch any fluid that may leak from the battery. If the fluid should come in contact with the eyes, mouth, or skin, wash immediately with water and consult a doctor. * Always dispose batteries in accordance with local laws and regulations. e Slide the battery holder back into the battery case and press firmly so that the battery holder locks in place. USING THE TUNER q Press the TUNER switch ( ) to activate the tuner. (The lamps light.) w Tune the guitar string until the note name of the desired pitch appears in the display. e The string is in tune when only the lamp lights in the center of the display. Pitch is low • • • In Tune • • • Pitch is high lamps are off.) r Press the TUNER switch agai n to switch the tu ner OFF ( ). (The * It may take a few seconds before the tuner can detect pitches after being switched ON. * The note name and displays may have difficulty keeping up with irregular pitch changes. Gradually change the pitch and check when tuning. * The tuner may not be able to detect notes rich with overtones or with very short sustain. * Sound output is muted when the tuner is in use. l Calibration (changing the reference pitch) Th...

Dieses Handbuch ist für folgende Modelle:
Musikinstrumente - A4K (1004.19 kb)
Musikinstrumente - AC4K (1004.19 kb)