Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Anleitung Zusammenfassung
53. CLEAN EFFECTS LOOP SEND: When using an external effect on the Clean channel, connect this jack to the effect’s input by means of a shielded signal cable. 54. TUNER OUT: Use this jack to connect an electronic tuner to the amplifier. The signal at this jack is always present, even when the Mute is engaged, allowing for silent tuning as well as a non-interrupted monitor feed. 5 6 Connections SVT-5 PRO Bass Amplifier MONO BRIDGED: The SVT-5 PRO’s two internal amplifiers are bridged together to produce maximum output power. • Full Range/Biamp switch out (full range), Stereo/Mono switch depressed (mono) • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Mono Bridge/Biamp Speakon® jack to the input of a full range speaker cabinet • Speakon® pin 1 + = signal “+,” pin 2+ = signal “–” MONO BRIDGE SVT-5 PRO IN OUT (MONO) 1 TO INPUT JACK FULL RANGE CABINET(S) NOTE: BE ABSOLUTELY CERTAIN THAT THE CABINET(S) ARE ABLE TO HANDLE THE EXTREMELY HIGH OUTPUT POWER OF THE AMP IN THIS MODE! (FULL RANGE) Mono Bridged DUAL MONO: The SVT-5 PRO’s two internal amplifiers will each power a full range cabinet. • Full Range/Biamp switch out (full range), Stereo/Mono switch out (stereo) • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Power Amp A jack to the input of a full range speaker cabinet • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Power Amp A jack to the input of a full range speaker cabinet SVT-5 PRO TO INPUT JACK TO INPUT JACK FULL RANGE CABINET(S) FULL RANGE CABINET(S) OUT OUT (STEREO) 2 1 (FULL RANGE) PWR AMP B PWR AMP A Dual Mono BIAMP - Full Range / Lows: One of the SVT-5 PRO’s internal amplifiers will power a full range cabinet, the other will power a low frequency cabinet. • Full Range/Biamp switch out (full range), Stereo/Mono switch out (stereo) • Connect a signal cable () from the SVT-5 PRO’s Biamp Low Output jack to its Amp A Power Amp Input jack • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Power Amp A jack to the input of a full range speaker cabinet • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Power Amp A jack to the input of a full range speaker cabinet SVT-5 PRO TO INPUT JACK TO INPUT JACK FULL RANGE CABINET(S) LOW FREQ. CABINET(S) OUT OUT (STEREO) 2 1 3 (FULL RANGE) PWR AMP B BIAMP LO OUT PWR AMP A AMP A PWR AMP INPUT Biamp - Full Range / Lows Use the Crossover Frequency control (#28) to set the crossover point for the low output. Connections SVT-5 PRO Bass Amplifier BIAMP - Highs / Lows: One of the SVT-5 PRO’s internal amplifiers will power a high frequency cabinet, the other will power a low frequency cabinet. • Full Range/Biamp switch depressed (biamp), Stereo/Mono switch out (stereo) • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Power Amp A jack to the input of a low frequency speaker cabinet • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Power Amp B jack to the input of a high frequency speaker cabinet – OR – • Connect a heavy duty four-conductor speaker cable () from the SVT-5 PRO’s Mono Bridge/Biamp Speakon® jack to the input of a biamp-equipped speaker cabinet • Speakon® pin 1 + = low “+,” pin 1– = low “–,” pin 2+ = high “+,” pin 2– = high “–” SVT-5 PRO TO INPUT JACK TO INPUT JACK HIGH FREQ. CABINET(S) LOW FREQ. CABINET(S) TO "BIAMP MODE" SPEAKON® JACK BIAMPEQUIPPED CABINET OUT IN (STEREO) 2 3 1 (BIAMP) PWR AMP B BIAMP PWR AMP A Biamp - Highs / Lows BIAMP WITH A SECOND AMP: The SVT-5 PRO’s two internal amplifiers will each power a low frequency cabinet. A second amplifier will power a high frequency cabinet. • Full Range/Biamp switch out (full range), Stereo/Mono switch depressed (mono) • Connect a signal cable () from the SVT-5 PRO’s Biamp High Output jack to the input jack of the second power amp • Connect a signal cable () from the SVT-5 PRO’s Biamp Low Output jack to its Amp A Power Amp Input jack • Connect a heavy duty speaker cable () from the second power amp’s Speaker Output jack jack to the input of a high frequency speaker cabinet • Connect a heavy duty speaker cable () from the SVT-5 PRO’s Mono Bridge jack to the input of a low frequency speaker cabinet • Speakon® pin 1 + = signal “+,” pin 2+ = signal “–” SVT-5 PRO SVT-5 PRO OR OTHER POWER AMP TO INPUT JACK TO INPUT JACK HIGH FREQ. CABINET(S) LOW FREQ. CABINET(S) IN OUT (MONO) 4 3 2 (FULL RANGE) MONO BRIDGE AMP A PWR AMP INPUT IN OUT (MONO) 1 (FULL RANGE) MONO BRIDGE BIAMP HI OUT BIAMP LO OUT AMP A PWR AMP INPUT Biamp with a Second Amp 7 Use the Crossover Frequency control (#28) to set the crossover point for the high and low outputs. Use the Crossover Frequency control (#28) to set the crossover point for the high and low outputs. 8 Some Suggested Settings SVT-5 PRO Bass Amplifier OUT OUT OUT IN OUT OUT OUT OUT IN OUT IN OUT IN OUT "SVT" "SMOOTH" IN IN IN IN OUT OUT "METAL" "SLAPPIN'" OUT OUT OUT OUT IN IN "EDGE" IN IN OUT OUT IN IN "SYNTH" IN IN OUT OUT IN IN "THREE GUYS JAMMIN'" SVT-5 PRO Bass Amplifier Rack Mounting When mounting the SVT-...