Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE. BA-210SP Bassamp Cube with Digital Effects IMPORTANT SAFEGUARDS AND PRECAUTIONS: All Ampeg products are designed for continuous safe operation. Abiding by the following rules can help prevent damage to your amplifier, yourself and others. • The amplifier is equipped with a three-pronged AC power cord. To reduce the risk of electrical shock, NEVER remove or otherwise attempt to defeat the ground pin of the power cord. • Connect the amplifier ONLY to a properly grounded AC outlet of the proper voltage for your amp. • Avoid sudden temperature extremes, rain and moisture. Also, avoid sudden and intense impact. (If the unit has been subjected to any of the preceding abuses, have it looked at by an authorized service center.) • Do not expose the unit to splashing or dripping liquid. Do not place liquid filled objects on the unit. · NEVER set the amplifier on a support that will not bear its weight. • Always keep the total speaker impedance at or above the rated load. • Unplug the amplifier before cleaning it. NEVER spray liquid cleaners onto the amplifier. Wipe it with a slightly dampened, lint-free cloth to remove dirt and film. • DO NOT use the amplifier if it has sustained damage to the chassis, controls, or power cord. Refer the unit to an authorized service center for inspection. • Prolonged exposure to high volume levels may cause permanent hearing loss or damage. Such damage is progressive and irreversible! BA-210SP Bassamp Cube with Digital Effects THE TOP PANEL: 1. 0dB I N P U T: Connect your “passive” bass guitar here using a shielded instrument cable. This input is not padded and is best suited for basses without active electronics. 2. -15dB I N P U T: Connect your “active” bass here using a shielded instrument cable. T h i s input is padded 15dB and is best suited for basses with active electronics and/or “hot” p i c k u p s . 3. VOLUME: Use this control in conjunction with your instrument’s volume controls to adjust the level of the signal sent to the preamp. For the best signal to noise ratio and maximum headroom, start with this control at 5 or greater. 4. STYLE: This five-position switch is used to control the tone of the amplifier. Experiment with the Style and other eq controls (#5,6,7) for the results which suit you best. The settings of the style control are as follows: 5. LOW: This control is used in conjunction with the style control to adjust the low frequency level of the amplifier. 6. MID: This control is used in conjunction with the style control to adjust the midrange level of the amplifier. 7. HIGH: This control is used in conjunction with the style control to adjust the high frequency level of the amplifier. 8. LEVEL: Use this control to adjust the level of the output signal from the amplifier. T h i s control also adjusts the signal level of the CD Inputs (#12), the Headphones jack (#13) and the Line Out jack (#15). 9. EFFECTS SELECT: Use this control to select the desired digital effect. A listing of the effects is shown on page 6. 10. EFFECTS A D J U S T: Use this control to adjust one of the parameters of the selected digital effect. A listing of the parameters for each of the effects is shown on page 6. BA-210SP Bassamp Cube with Digital Effects 11. EFFECTS LEVEL: Use this control to adjust the level of the selected digital effect. 12. CD INPUT: Use these RCA jacks to connect the line level (or headphones) output of a CD player, tape deck or rhythm machine to the amplifier. The inputs to these jacks are summed into a mono signal which is fed into the BA210SP’s power amplifier. The signal level from these jacks is adjusted by the amplifier’s Level control (#8). If the signal from the source connected to these jacks is too strong, use the output level control on the source to adjust the signal to obtain the proper level for a good mix. 13. HEADPHONES: Use this jack to listen to the amplifier through a pair of stereo headphones. The internal speaker is disconnected when the headphones jack is used. 14. FOOTSWITCH: Use this jack to connect the supplied two button footswitch to the amplifier for remote control of the digital effects. For information on programming the footswitch, see page 7. 15. BAL. LINE OUT: This jack supplies a post-eq, balanced line level signal for connecting to a house sound board, recording unit or external amplifier. 16. POWER: Use this switch to turn the amplifier on or off. The adjacent LED will illuminate when the amplifier is turned on. 17. A C L I N E C O R D (rear panel, not shown): This heavy duty, grounded, three wire power cord is to be plugged into a safely-wired, grounded, 120 volt, 60 cycle A C power outlet. DO N O T attempt to defeat the ground connection of this cable! If your amplifier was purchased outside of the United States, see the unit’s rear panel for its power and voltage ratings and follow the above guidelines. BA-210SP Bas...