Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The Vintage features a 110 watt (RMS) tube type chassis with more than enough punch to be heard over larger and more powerful amps. The Vintage features volume, treble, middle, and bass controls. Reverb is also starTdard on all Vintage models. The open back cabinets of the Vintage series lend to their "singing" quality and the harmonics of the amp enable the performer to get clean sound, as well as natural distortion with tremendous sustaining quality. We now offer three models of the Vintage to allow the performer to choose either 10 or 12 inch speakers in several combinations for maximum tonal versatility. Matching extension speakers are also available. (1,2) Normal channel input jacks provide the complete tonal range of the amplifier and should normally be used unless the bass rolloff of the bright channel is desired. The gain of the normal channel is slightly more than the bright channel. This increased gain is useful when adjusting the master volume control for harmonic effects. (3,4) Bright channel input jacks provides a Bass rolloff, allowing more of the high frequencies to come through. (5) The volume control serves to control the gain of the preamp. This preamp circuit makes possible exceptional gain and input imdedance while allowing the amplifier to provide tremendous dynamic range. Please remember that the volume control of the vintage controls the SENSITIVITY of the preamp, not the POWER of the amp. It is entirely possible for the amp to be driven to full power output on very low volume settings if the signal from your instrument is extremely high. (6) The bass control varies the amount of bass response in the system and is very effective in achieving a balanced tonal blend. (7) The middle control enables the musician to tailor the vital mid-range response. Experimentation with, the unique middle circuit will show that it is much more effective than conventional circuits. (8) The treble control varies the high end response of the amplifier. (9) The reverb control determines the amount of delayed signal (reverb) blended into the output. This circuit is able to produce tremendous sustain and clarity by properly damping the driver coils of the reverb unit. The reverb is effective in BOTH channels. (10) The master volume control is very useful for obtaining a number of effects. The most common use of this control is for obtaining overdrive and sustain at low sound levels. Another valuable use for this control is for controlling the response and noise of the amp in a recording studio. The master volume control is the final gain determining element before the signal is fed into the output amplifier and could more accurately be called a "sensitivity" control. To obtain maximum overdrive and sustain, the individual channel volume controls should be set near maximum, and the output of the system should be adjusted with the master volume control. You will discover that many different and pleasing harmonic effects can be obtained by trying different settings of the tone, volume, and master volume controls. It has been found that when operating the amp in the overdriven condition, lower settings of the treble control tend to give a smoother "natural distortion characteristic". The normal background noise (hiss, hum. etc.) can be very effectively controlled for recording studio applications by use of the master volume control. To reduce these noises, reduce the setting of the master volume control. 01) The pilot light indicates when the electrical supply (mains) is supplying power to the amplifier. (12) The Standby switch allows the operator to cut the amp off without shutting off the tube filaments. This places the amp in a "Standby" mode which eleminates the warm up time for the tube filaments when the amp is switched on. (13) The on/off switch is a two position switch which cuts the amp on and off. (14) The fuse is located within the cap of the fuse holder and should be replaced with one of the proper value if it should fail. It is necessary that the proper value fuse be used to avoid damage to the equipment and to avoid voiding the warranty. If your amplifier repeatedly blows fuses, the unit should be taken to a qualified service center for repair. (15) The ground switch is a two position switch which is used to ground the amplifier properly. One of the positions will yeild the least hum or popping when the instrument is touched, and this is the position that s...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - Vintage (765.87 kb)