Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
But note that all values return to their defaults at power-off. B ON switch Switches use of the internal effector on or off. The internal effect is applied only if this switch is on. Note that the lamp above the switch lights up orange to indicate that the switch is on. As an alternative to the ON switch, you can use a separately sold FC5 foot switch to toggle the effector on and off. NOTE The internal effector is automatically turned on whenever you switch on the mixer’s power. C EFFECT OUT jack This unbalanced phone output jack outputs the signal from the EFFECT bus. You can use this jack to output the signal to an external effector. You can then return the signal by connecting the external effector to any of the LINE jacks on channel pairs 5/6 to 11/12. If you are returning a signal from an external effector into a LINE jack on any channel pair 5/6 to 11/12, please be sure to turn the EFFECT knob for that channel pair to “0”. D FOOT SW jack This phone input jack can connect to the (separately sold) YAMAHA FC5 foot switch. With the foot switch connected, you can use your foot to toggle the internal effector ON and OFF. 22 EMX512SC/EMX312SC/EMX212S Controls and Connectors Controls and Connectors n FGHEIJ E Graphic Equalizer This 7-band graphic equalizer adjusts the frequency characteristics of the stereo signal on the MAIN L and MAIN R buses. This is the signal that is output to the MAIN OUT jacks I and to the SPEAKERS jacks V. Each band can be adjusted by ±12 dB. The base frequencies for the bands are: 125, 250, 500, 1k, 2k, 4k and 8k Hz. F EFFECT RETURN knob Adjusts the level of the signal sent from the internal effector to the MAIN L and MAIN R buses. G MASTER knob Adjusts the level of the signal output to the SPEAKERS jacks V and MAIN OUT jacks I. H LEVEL meters The L and R meters show the level of the signal output from the MAIN OUT jack I. The MAIN OUT signal also passes through the internal power amp and is then output at the SPEAKERS jacks V. Keep an eye on the LIMITER lamps Q to ensure that the level at the SPEAKERS jacks does not stay too high. I MAIN OUT L and R jacks These unbalanced phone output jacks feed out the main stereo output. You would typically connect these jacks to a power amp or powered speakers. The signal sent to these jacks is adjusted by the MAIN section’s MASTER knob G and graphic equalizer E. J REC OUT L and R jacks These RCA pin-type unbalanced output jacks can be used to send the main stereo signal to an external DAT recorder or cassette recorder. Note that unlike the output from the MAIN OUT jacks, the signal from the REC OUT jacks is not adjusted by the MAIN section’s MASTER knob G and graphic equalizer E. NOTE Since this output signal is not adjusted by the MAIN section’s MASTER knob G, you should adjust the level as necessary at the recording side. EMX512SC/EMX312SC/EMX212S 23 Controls and Connectors Controls and Connectors n LMNKO K Graphic Equalizer This 7-band graphic equalizer adjusts the frequency characteristics of the monitor signal that feeds to the MONITOR OUT jack O and (if the POWER AMP switch is down) to the SPEAKERS B jacks V. Each band can be adjusted by ±12 dB. The base frequencies for the bands are: 125, 250, 500, 1k, 2k, 4k, and 8k Hz. L EFFECT RETURN knob Adjusts the level of the signal sent from the internal effector to the MONITOR bus. M MASTER knob Adjusts the level of the monitor signal send to the MONITOR OUT jack O and (if the POWER AMP switch is down) to the SPEAKERS B jacks V. N LEVEL meters The L and R meters show the level of the signal output from the MONITOR OUT jack O. If the POWER AMP switch is down, the MONITOR OUT signal also passes through the internal power amp and is then output at SPEAKERS jacks B1 and B2 V. Keep an eye on the LIMITER lamps Q to ensure that the level at the SPEAKERS jacks does not stay too high. O MONITOR OUT jack This unbalanced phone jack outputs the monaural monitor signal. You would typically connect this jack to powered speakers used for monitoring. The signal sent to this jack is adjusted by the MONITOR section’s MASTER knob M and the settings of the MONITOR section’s graphic equalizer K. 24 EMX512SC/EMX312SC/EMX212S Controls and Connectors Controls and Connectors n PRSTUQ P PHANTOM switch This switch toggles +15V phantom power on and off. If you set the switch on, the mixer supplies power to the XLR mic input jacks on all channels (the INPUT B jacks on channels 1 to 4, and the MIC jacks on channel pairs 5/6 to 11/12). Set this switch on when using one or more condenser microphones. NOTE When this switch is on, the mixer supplies DC +15V power to pins 2 and 3 of all XLR input jacks. • Be sure to leave this switch off if you do not need phantom power. • When using phantom power, do not connect any devices other than condenser microphones to the XLR input jacks. Other devices may be damaged if connected to phantom power. This precaution does not apply to balanced dynamic microphones, however, as these will not b...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - EMX212S (2.83 mb)
Musikinstrumente - EMX312SC (2.83 mb)