Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Internal jumpers allow the AUX 1 and AUX 2 controls to be rewired for pre-EQ/pre-fader or post-EQ/pre-fader operation if required (refer this job to qualified YAMAHA service personnel). r note: - AUX 3 and AUX 4 are factory pre-wired for pre-EQ/ pre-fader operation, so the AUX 3 and AUX 4 signals are not affected by EQ or fader settings. Internal jumpers allow the AUX 1 and AUX 2 controls to be rewired for post-EQ/pre-fader or post-EQ/post-fader operation if required (refer this job to qualified YAMAHA service personnel). /Is - LEFT SPEAKER RIGHT SPEAKER _ - \i/ \l/ /|\ ^.l/_ IQ) PAN -4 - O Channel Fader This is the main level control for each input channel. It determines the level of the signal sent from the corresponding input channel to the master stereo buss. The settings of the 16 input faders determines the “mix” or balance of sound levels between the instruments or other sources connected to the inputs. Master Control Section r NOTE: - If a channel is not being used, its fader should be set to the lowest position (“0” on the scale) to prevent unwanted noise from being added to the main program signal. - STEREO CHANNEL NOTE: - On channels 15 and 16, the channel fader simultaneously controls the levels of signals received via the channel’s L and R inputs. POWER 10 9 8 7 6 5 4 3 • 2 1 -i -10 10- -9 9- -8 8--7 7--6 6- - 5 5- -4 4- -3 3- -2 2- 1-1 1 -r -0 0- -10 -9 -8 - 7 -6 - 5 -4 -3 -2 ©- L STEREO R - 5 - FRONT PANEL CONTROLS 0 AUX SND 1, 2, 3 and 4 Controls These adjust the overall output level of the AUX 1, AUX 2, AUX 3 and AUX 4 “mixes” set up using the AUX 1 through AUX 4 controls on channels 1 through 16. AUX SND 1 sets the overall level of the AUX 1 mix signal appearing at the AUX SEND 1 jack, AUX SND 2 sets the overall level of the AUX 2 mix signal appearing at the AUX SEND 2 jack, and so on. These controls should be used to optimally match the AUX SEND output level of the MV1602 to the input sensitivity of the signal processing device, amplifier or other equipment used. 0 AUX RTN 1, 2, 3 and 4 Controls •These controls adjust the level of the signal received at the rear-panel AUX RETURN jacks and mixed into the main stereo program. Since stereo AUX returns are provided, all four AUX RTN controls are “ganged types, simultaneously controlling the AUX RTN levels to the left and right stereo buss. 0 STEREO L and R Master Faders The STEREO L and R faders Independently adjust the level of the signal sent from the left and right master stereo busses to the L and R STEREO OUT connectors. 0 STEREO L and R Level Meters The MV1602 features independent 10-element LED peak level meters for the left and right channels. The LED elements correspond to levels of °°, -20, -15, -10, -6, -3, 0, +3, and +6 dB. The topmost “CLIP” elements are provided to warn of possible overload distortion. If either of the CLIP elements lights more than just occasionally on high-level peaks, the channel fader levels or levels of the sources connected to the mixer’s inputs should be reduced. 0 AUX 1/3 and 2/4 Level Meters and METER SELECT Switches 10-element LED peak level meters (°°, -20, -15, -10, -6, -3, 0, +3, and +6 dB) are also provided for AUX buss level monitoring. The AUX 1/3 meter displays signal levels on the AUX 1 buss or AUX 3 buss, depending on the setting of the METER SELECT switch immediately below it, and the AUX 2/4 meter displays signal levels on the AUX 2 or AUX 4 buss, depending on the setting of the METER SELECT switch immediately below it. The topmost “CLIP” elements are provided to warn of possible overload distortion. If either of the CLIP elements lights more than just occasionally on high-level peaks, the AUX control levels should be reduced. 0 LEVEL Control and PHONES Jack The PHONES jack delivers the master stereo program signals to a pair of 8 — 40 ohm stereo monitor headphones. The LEVEL control adjusts the headphone monitoring level. 0 POWER Switch Press once to turn power ON, and a second time to turn power OFF. The LEDs of the stereo level meter will light when the power is ON. -6- REAR PANEL CONNECTORS AND CONTROLS m o @ o o @ o _o_ © ©