Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
The ON Switch is a temporary ON type (push-on/release-off) —the talkback signal is applied to the selected buss(es) only when the ON switch is held ON. © Talkback Assignment Switches These switches determine to which buss(es) the talkback signal is applied. The talkback signal can be assigned tp group busses 1 and 2 (1-2), group busses 3 and 4 (3-4), AUX buss 1 (AUX1), AUX buss 2 (AUX2), AUX buss 3 (AUX3) and/or the stereo buss (ST). © ST L & R Faders These faders independently adjust the level of the signal sent from the left and right stereo busses to the ST OUT connectors and the console's monitor system when the MONITOR ST source select switch is ON. © VU Meters and Select Switches The MR-series consoles feature six precision illuminated VU meters with built-in PEAK LEDs. The leftmost four meters can be switched to show signal levels on group busses 1, 2, 3 and 4, or AUX busses 1 — 3 and the CUE buss, respectively. The rightmost two meters show levels on the left and right stereo busses. The PEAK LEDs built into each meter light when the corresponding signal level reaches +14 dB. 8 REAR PANEL CONNECTORS AND CONTROLS Rear Panel ® POWER Switch Flip to the ON position to turn power ON, and to the OFF position to turn power OFF. The VU meter illumination will come on when the power is ON. CAUTION: Make sure the GROUP and STEREO faders are set to minimum when turning the POWER switch ON. ® Hl-Z and LO-Z Input Connectors Each input channel offers a choice of two input connectors: a balanced LO-Z (low-impedance) XLR-type connector and a balanced Hl-Z (high-impedance) tip-ring-sleeve 1/4" phone jack. The LO-Z inputs are primarily intended for use with professional low-impedance microphones or electronic instruments having low-impedance balanced outputs. The Hl-Z jnputs will accept either balanced or unbalanced signals from high-impedance microphones, musical instruments or other source equipment. The LO-Z and Hl-Z inputs accept nominal 50Q— 600£2 microphones or 600Q lines, respectively. Nominal input level is between -60 dB and 0 dB, depending on the settings of the channel GAIN control and PAD switch. Refer to "Connecting Sources" on page 13 for more information. ® INSERT -6dB Jack This is a TRS (Tip-Ring-Sleeve) type jack that provides an insert patch point for connection of external signal processing or other equipment between the channel's head amplifier (the first amplifier stage after the input) and EQ stage. The insert points are ideal for insertion of compressors, noise gates, equalizers or other equipment that needs to be applied to specific channels only. The INSERT-6dB jack includes both the send (output) and receive (input) lines required by the insert point, sending and receiving signals at a nominal -6dB. TRS PHONE PLUG Tip (Insert receive) fp__|-too to IN jack <4t " ■ Sleeve(Ground) Ring (Insert send) -1 Ibjo to OUT jack TAPE Input Jack This -10 dB RCA pin jack input is ideally suited for receiving line-level sources such as the output from a tape recorder or similar equipment. The front-panel TAPE switch determines whether input for that channel is received via the LO-Z/HI-Z connectors or the TAPE jack. 9 ® AUX SEND+4dB 1, 2 & 3 Jacks These jacks deliver the AUX 1, AUX 2 and AUX 3 mixes, respectively, to feed an external signal processor, performer's headphone cue system, a monitor system, etc. Nominal output level of the AUX send jacks is +4 dB. ® AUX RTN +4dB 1 (L & R) & 2 (L & R) Jacks The output from signal processors fed by the AUX SEND 1, AUX SEND 2 and/or AUX SEND 3 jacks can be returned to the group and/or stereo busses via these jacks. Stereo AUX RTN jacks offer compatibility with the wide range of mono-in/stereo-out signal processors currently available. The AUX RTN jacks can also be used to add external signals other than the output from signal processor to the group and/or stereo busses. Nominal input level/impedance is +4 dB/600£l ® GROUP INSERT 1,2,3 &4 Jacks These TRS phone jacks function in the same was as the channel INSERT-6dB jacks, allowing external signal processing equipment to be inserted into the group-circuit signal paths immediately prior to each GROUP fader. Wiring of the GROUP INSERT jacks is exactly the same as the channel INSERT-6dB jacks. ® STEREO L SUB IN & STEREO R SUB IN Jacks The STEREO SUB IN jacks provide direct inputs to the console's left and right stereo busses. The STEREO SUB IN jacks can be used alone or in conjunction with the GROUP SUB IN jacks to "cascade“ two MR-series consoles together — the STEREO OUT connectors of one console are connected to the corresponding STEREO SUB IN jacks of the second console. The STEREO SUB IN jacks have an input level of +4 dB and are designed for used with 600Q lines (nominal). ® GROUP OUT +4dB/-10dB 1,2,3 & 4 Connectors These are the main outputs from the console's four group busses. The XLR type connectors provide balanced line output at +4 dB (nominal), 600 £2. The RCA pin jacks de...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - MR1642 (1.17 mb)
Musikinstrumente - MR842 (1.17 mb)