Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
The switches can be turned on/off individually. H OSCILLATOR select switch These switches select the type of test oscillator, and begin oscillation. Only one can be selected at a time. The corresponding indicator will light to indicate the switch which is currently on. lPINK switch Pink noise will be produced. l10 kHz/1 kHz/100 Hz switches A sine wave of the corresponding frequency will be produced. I OSCILLATOR OFF/ ON switch This is an off/on switch for the oscillation of the oscillator. J MIC jack This is an XLR-3-31 input jack (unbalanced) for connecting a talkback mic. It can be used with mics of 50– 600 ohms impedance. K LEVEL control This control adjusts the level of talkback or the oscillator. L ON switch This switch turns talkback on/off. When this is on, the indicator located above the switch will light. If you wish to use the oscillator, turn this switch off. TALKBACK MIC OSCILLATOR 100Hz 1kHz 10kHz PINK ST M13-M16 M1-M2 M3-M4 M9-M12 M7-M8 M5-M6 ON LEVEL 0 10 A B C D E F G I J K L H OFF/ ON Note: The oscillator cannot be used in conjunction with talkback. In order to use the oscillator, you must turn off the talkback ON switch (L). ST LEVEL BA OFF/.ON MIC HA ST L R MIX (FIX) MIX (VARIABLE) 1 3 5 7 1 2 3 4 5 6 7 8 2 4 6 8 9 11 13 15 10 12 14 16 M1-M2 M3-M4 M5-M6 M7-M8 M9-M12 M13-M16 from..Osillator Control panel Control panel n In this section you can select the source whose level will be shown in the meter bridge section. Only one of the sources 1–3 can be selected. METER SEL M9-M16 M1-M8 MATRIX A B C A M1–M8 switch When this switch is turned on, the M1/M9/ MATRIX1–M8/M16/MATRIX8 meters (page 25) will show the output levels of MIX OUT 1–8. At this time, the indicator located at the left of the switch will light. B M9–M16 switch When this switch is turned on, the M1/M9/ MATRIX1–M8/M16/MATRIX8 meters (page 25) will show the output levels of MIX OUT 9–16. At this time, the indicator located at the left of the switch will light. C MATRIX switch When this switch is turned on, the M1/M9/ MATRIX1–M8/M16/MATRIX8 meters (page 25) will show the output levels of MATRIX OUT 1–8. At this time, the indicator located at the left of the switch will light. Control section On the M3000A, on/off settings for the mono/stereo input channels, the output channels of the mix sections, and STEREO A OUT can be stored as a “scene” (memory numbers 1–128 can be rewritten, and 129– 130 are read-only). In this section you can save and read scene memories. (For details on using scene memories, refer to page 31.) DIRECT RECALL 8 7 6 5 4 3 2 1 SCENE MEMORY ENTER 9 0 87 5 6 43 21 CHECK STORE MEMORY RECALL UTILITY A B C D 8 E G 6 Control panel Control panel When you are in Utility mode (refer to page 34), the indicator located above the switch will light. B RECALL switch Use this switch to recall scenes from scene memory. If you select a scene which has not been stored and attempt to recall it, the MEMORY display (3) will indicate “ ” (No data) for approximately two seconds. C MEMORY display This is a three-digit LED display. In normal mode and in check mode, it displays a scene memory number 1–130. Concerning the decimal point display This will light if the This will light when In normal mode, this display number bulk data is being will light when you have contains no data. If received from the modified the settings of all memories contain MIDI IN connector. the last-recalled scene. no data, this dot will In check mode, this will light when the M3000 light when you have is powered-on. modified the settings of the selected scene. In utility mode, utility-related parameters are displayed here (for details refer to page 34). D STORE key Use this key to store a scene into scene memory. When you press this switch once, the display will indicate “ ,” notifying you that the scene may now be stored. At this time press the button once again to execute the Store operation. If you decide not to store the scene, simply press any other button. Before storing a scene memory, make sure that the Memory Protect setting (page 34) is turned OFF. E CHECK switch Use this to switch from normal mode to check mode (refer to page 33). In check mode, the indicator located above the switch will light. F 0–9/ENTER buttons Use these to numerically specify a scene memory number. Use the 0–9 switches to enter a value, and press the ENTER button to finalize that value. G s /t switches Use these to step through scene memory numbers consecutively. However, the read-only scenes in memory numbers 129/130 cannot be selected by these switches, and must be selected using the 0–9/ENTER buttons (6). These switches are also used to select parameters in Utility mode. However in Utility mode when the oP (recall operation) parameter is set to “ ,” scenes in memory numbers 1–8 cannot be selected by these switches, and must be selected using the 0–9/ENTER buttons. If either switch is held for longer than one second, the value will change rapidly. (For details on parameter cont...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - M3000A-32 (621.46 kb)
Musikinstrumente - M3000A-40C (621.46 kb)
Musikinstrumente - M3000A-56C (621.46 kb)