Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• CIB1D : Console interface board • EMB1D : Engine management board • PDB1D : Patch DSP board • GDB1D : Group DSP board • EDB1D : Effect DSP board • IDB1D : Input DSP board ¦ Front panel ¦ Rear panel Thank you for choosing the DSP unit “DSP1D/DSP1D-EX”, specifically designed for the Yamaha PM1D digital audio mixing system. The DSP1D/DSP1D-EX is an engine controlled by the CS1D control surface. Be sure to ask an authorized Yamaha service engineer to install the boards and set up the unit. Never perform installation and setup by yourself. POWER ON/ OFF A B ENGINE ID 1 2 CONTROL I/O 48CH 96CH INPUT CONFIGURATION POWER ON/ OFF A B ENGINE ID 1 2 CONTROL I/O 48CH 96CH INPUT CONFIGURATION 1 2 3 4 2 2 2 2 IN OUT IN 2 OUT IN 1 1 IN 5 3 1 9 7 5 3 1 2 OUT 6 4 2 10 8 6 4 2 OUT THRU PC CONTROL WORD CLOCK TIME CODE IN GPI RS-422 REMOTE IN OUT OFF ON RS-232-C USB 75. MIDI OUTPUT INPUT CONTROL I/O CONSOLE CONSOLE I/O CASCADE DIGITAL I/O 1 IN 5 3 1 9 7 5 3 1 2 OUT 6 4 2 10 8 6 4 2 CONSOLE OUTPUT INPUT I/O CASCADE DIGITAL I/O 2 2 2 2 IN OUT IN 2 OUT IN 1 OUT THRU PC CONTROL WORD CLOCK TIME CODE IN GPI RS-422 REMOTE IN OUT OFF ON RS-232-C USB 75. MIDI CONTROL I/O CONSOLE 5 M N O 6 7 8 9 J K L P A Anected to the engine A channel jacks of the CS1D control surface (DIGITAL I/O jack A and CONTROL I/O jack A). Indicator B lights up if the DSP1D/DSP1DEX is connected to the engine B channel jacks of the CS1D control surface (DIGITAL I/O jack B and CONTROL I/O jack B). Error indication • If both ENGINE ID A and B indicators are flashing: > There is a malfunction in the internal board (PDB, GDB, IDB1/2, EDB, EMB, or CIB). Or the necessary board does not exist. • If either ENGINE ID A or B indicator is flashing: > During the Mirror mode operation, the ENGINE ID indicator for the unused DSP1D/ DSP1D-EX flashes, indicating that the unit is in standby mode. > If Indicator A is flashing, unit A is in standby mode. If Indicator B is flashing, unit B is in standby mode. B CONTROL I/O 1/2 indicators These indicators indicate which one of two CONSOLE 1, 2 IN/OUT jacks (8) on the rear panel is currently effective. Note: When you turn on the power to the DSP1D/ DSP1D-EX and the CS1D, and communication between the DSP1D/DSP1D-EX and the CS1D is established, one of these two indicators lights up. If neither one lights up, check the connection of the CONSOLE 1, 2 IN OUT jacks on the rear panel. Error indication • If the CONTROL I/O 1 indicator is flashing: > Communication between the CS1D control surface and the DSP1D is not established.The CONSOLE 1, 2 IN OUT jacks or the PC CONTROL port is not connected correctly. C INPUT CONFIGURATION 48CH/96CH indicators These indicators indicate how many input channels are currently available. On the DSP1D, the 48CH indicator lights up. On the DSP1D-EX, the 96CH indicator lights up. Error indication • If the INPUT CONFIGURATION 48CH is flashing: > The signal is not locking to the word clock. D POWER ON/OFF switch Use this switch to turn the power to the DSP1D/ DSP1D-EX on or off. When the power is turned on, the indicators 1 -3 light up. E MIDI IN/OUT/THRU connectors These connectors are used to transmit and receive Program change messages, MMC, and other MIDI messages among external MIDI devices. F PC CONTROL RS-232-C/USB ports Connect these ports to a PC that runs Windows 2000 or Windows XP to control the PM1D system from the PC. Use a D-sub, 9-pin cross cable (female to female) to connect the RS-232-C port to the serial (COM) port on the PC. Alternatively use a USB cable to connect the USB port to the USB port on the PC. G WORD CLOCK IN jack, 75 . ON/OFF switch, and WORD CLOCK OUT jack The WORD CLOCK IN jack is used to provide word clock to the PM1D system from the connected external device, such as a clock generator. Use the WORD CLOCK OUT jack to provide the word clock to the connected external device from the PM1D. Use a BNC cable with an impedance of 75 . for the WORD CLOCK IN/OUT jacks. The WORD CLOCK ON/OFF switch is used to terminate the word clock connection. Basically, if the DSP1D/DSP1D-EX is the last device of the word clock chain, or if nothing is connected to the WORD CLOCK IN/OUT jacks, set this switch to ON. H CONSOLE 1, 2 IN/OUT jacks These jacks are connected to the CONTROL I/O CONSOLE jacks of the CS1D control surface to transmit or receive control signals. For connection, use a genuine Yamaha cable or a BNC cable with an impedance of 50 .. I REMOTE RS-422 connector This D-sub 9-pin connector is used to control a connected tape recorder or a hard disk recorder. Serial commands can be transmitted through this connector to play or stop such a recorder. J GPI connector This connector is used to connect an external device that supports GPI (General Purpose Interface), such as a video editor to control the external device from the PM1D system or to perform certain functions of the PM1D system while controlling from the external device. You can connect a custom-made external switch here. K TIME ...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - DSP1D-EX (181.14 kb)