Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Yamaha, modell CL5

Hersteller: Yamaha
Dateigröße: 245.88 kb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Dieses Gerät hat auch andere Anweisungen:

Musikinstrumente - CL5 (361.96 kb)

Musikinstrumente - CL5 (243.27 kb)

Musikinstrumente - CL5 (4.57 mb)

Musikinstrumente - CL5 (91.74 kb)

Alle anzeigen

Musikinstrumente - CL5 (9.52 mb)

Musikinstrumente - CL5 (449.97 kb)

Musikinstrumente - CL5 (3.2 mb)

Musikinstrumente - CL5 (1.72 mb)

Musikinstrumente - CL5 (3.55 mb)

Musikinstrumente - CL5 (4.54 mb)

Musikinstrumente - CL5 (18.98 mb)

Musikinstrumente - CL5 (608.94 kb)

Musikinstrumente - CL5 (3.84 mb)

Musikinstrumente - CL5 (1.75 mb)

Musikinstrumente - CL5 (6.29 mb)

Musikinstrumente - CL5 (19.21 mb)

Musikinstrumente - CL5 (6.33 mb)

Musikinstrumente - CL5 (4.26 mb)

Musikinstrumente - CL5 (19.06 mb)

Musikinstrumente - CL5 (608.1 kb)

Musikinstrumente - CL5 (3.54 mb)

Musikinstrumente - CL5 (1.73 mb)

Musikinstrumente - CL5 (6.28 mb)

Before changing the setting, first disconnect the cables. 2. Confirm the SECONDARY PORT setting for the CL series and the DIP switch setting on the I/O rack. 3. Turn the CL series and I/O rack off, then on again. 4. After waiting about 1 minute, plug the Ethernet cable into the Dante connector on the I/O rack, and then wait about 20 seconds before plugging the Ethernet cable into the Dante connector on the CL series. Changing the ID 1. Turn off the CL series. 2. Turn the I/O rack off, then on again. 3. Wait about 1 minute, and then turn on the CL series. NOTE If the CL series cannot be turned off, unplug the Ethernet cable from the Dante connector on the I/O rack, turn off the I/O rack while it is disconnected from the network, then turn it on again, and then wait about 1 minute before connecting the Ethernet cable. I/O rack settings for scene recall (Reference Manual, p. 198) For each CL series unit, you can specify which I/O rack the information saved on the CL series will be applied to when the CL series is started up and when a scene is recalled. When there are multiple CL series units, specify the settings so that a scene is recalled to an I/O rack from only one CL series. Follow the steps below. 1. In the Function Access Area, press the SETUP button. 2. Press the DANTE SETUP button to access the DANTE SETUP popup window. 3. In the DEVICE TYPE list, set the DEVICE TYPE for the I/O rack that you want recalled from the currently selected CL series to an I/O rack indicated by “(w/RECALL)”. 4. In the same way, for other CL series units, specify the DEVICE TYPE setting to set whether or not a scene is recalled to an I/O rack. NOTE . General network settings (BIT/LATENCY/W. CLOCK) from the CL series where CONSOLE ID is set to #1 are applied globally. . The head amp of the I/O rack can even be operated from a CL series where “(w/RECALL)” is not set. . An I/O rack where “(w/RECALL)” is set for one CL series cannot be set with “(w/RECALL)” for a different CL series. C.S.G., Pro Audio Division ©2012 Yamaha Corporation 205YJ-A0 ...