Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
2Center channel mode indicators The name of a selected center channel mode lights up only when a program which uses the Dolby Pro Logic Surround decoder is selected. 3EFFECT OFF indicator Lights up if neither the digital sound field processor nor the Dolby Pro Logic Surround decoder is on. In this state, sound output is 2-channel stereo. 5 4TAPE MON indicator Lights up when the tape deck (or MD recorder etc.) is selected as the input source by pressing the TAPE (MD) MONITOR button. 5DSP program indicators The name of a selected DSP program lights up when the built- in digital sound field processor and/or the Dolby Pro Logic Surround decoder is on. SPEAKER BALANCE ADJUSTMENT This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround decoder. The adjustment of each speaker output level should be done at your listening position with the remote control transmitter. Otherwise, the result may not be satisfactory. Note If this unit is connected with a Dolby Digital (AC-3) Decoder and/or an amplifier (or receiver) equipped with the Dolby Pro Logic Decoder or the digital sound field processor, also make an output balance adjustment using the test tone on each unit. NATURAL SOUND AV PROCESSOR/AMPLIFIER DSP–E492 CINEMA DSP POWER VOLUME l6 20 28 40 60 l2 8 4 2 0 –dB DELAY/ CENTER/REAR CENTER MODE TIME/LEVEL INTERNAL EXTERNAL VCR DVD/LD 2CH/6CH TV/DBS TAPE (MD) MONITOR TUNER (LINE 2) CD (LINE 1) PS EON INFO AFFAIRS SPORT NEWSRT CTPTY 0 20 l0040 60 EFFECT PRO LOGIC ENHANCED MONO MOVIE STADIUM PROCESSOR SELECTOR DISCO ROCK CONCERT CONCERT HALLCONCERT VIDEO 2 1 4, 8 7 5 6 REC/PAUSEDIR BDIR A PLAY DISC 2CH/6CH VOLUME PLAY PRESET A/B/C/D/E– + TIME/ LEVEL TEST EFFECT PROGRAM PROLOGIC ENHANCED – + TAPEA/B TUNER L2 CD L1 DELAY/CENTER/REAR/SWFR DVD/LDVCR TV/DBS 1 Set to the “°” position. l6 20 28 40 60 l2 8 4 2 0 –dB VOLUME 2 Turn on the power of this unit and the external amplifier etc. POWER 3 Set the balance control, tone controls, etc. on the external amplifier to the “flat” position. 4 TEST 5 Select the center channel output mode suitable for your speaker configuration. (Refer to “SPEAKER CONFIGURATION” on page 7.) CENTER MODE NORMAL WIDE PHANTOM On the feature of each mode, refer to the “Note” shown below. Note In step 5, when you select a center channel output mode, note the following. For 5-speaker configuration) NORMAL: Select this mode when you use a center speaker that is smaller than the main speakers. In this mode, the bass tone will be output from the main speakers. WIDE: Select this mode when you use the center speaker approximately same sized as the main speakers. For 4-speaker configuration) PHANTOM: Select this mode when you do not use the center speaker. The center sound will be output from the left and right main speakers. English 6 Turn up the volume. VOLUME 8 Cancel the test tone. TEST Disappears. You will hear a test tone (like pink noise) from the left main speaker, then the center speaker, then the right main speaker, and then the rear speakers, for about two seconds each. The display changes as shown below. Main (L) Center Rear (L and R) Main (R) * The test tone from the left rear speaker and the right rear speaker will be heard at the same time. 7 Adjust the sound output levels of the center speaker and the rear speakers so that they become almost as same as that of the main speakers. a) Press once or more so that “CENTER” or “REAR” appears on the display. * Select “CENTER” to adjust the output level of the center speaker, and select “REAR” to adjust the output level of the rear speakers. DELAY/CENTER/REAR/SWFR Notes . Once you have completed these adjustments, you can adjust whole sound level on your audio system by using this unit’s VOLUME control (or the VOLUME keys on the remote control transmitter) only. . You may also use the volume controls on the external amplifiers etc. to achieve proper balance. . In step 7, if the center channel mode is in the “PHANTOM” position, the sound output level of the center speaker cannot be adjusted. This is because in this mode, the center sound is automatically output from the left and right main speakers.