Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
GND terminal (For turntable use) Connecting the ground wire of the turntable to this terminal will normally minimize hum, but in some cases better results may be obtained with the ground wire disconnected. PRE OUT/MAIN IN terminals Removing the jumper pins enables this unit to independently perform the functions of a control amplifier and a power amplifier. These terminals are for connection of a signal- processing system such as a graphic equalizer or sound processor. If a sound processor or other external unit is connected between these terminals, the VOLUME control of this unit can be used for overall adjustment of the level of sound. To connect such a unit, remove the jumper pins from the PRE OUT/MAIN IN terminals, connect the inputs of that unit to the PRE OUT terminals and its outputs to the MAIN IN terminals. For details, refer to the owner’s manual included with the unit to be connected. MAIN IN COUPLER PRE OUT R L Notes . If you will not use the PRE OUT/MAIN IN terminals, never remove the jumper pins from these terminals. If removed, no sound will be output from this unit. . If you will use this unit with an external unit connected between the PRE OUT and MAIN IN terminals, make sure that the PURE DIRECT switch on the front panel is turned off. . If you will use this unit as a power amplifier, connect the outputs of an external control amplifier etc. to this unit’s MAIN IN terminals. In that case, this unit’s controls will not function except the PHONES jack and the SPEAKERS switches, so use the controls on the external control amplifier to make volume adjustment etc. OPERATIONS 7 2 1, 6 TO PLAY A SOURCE 4 73 1 Set to the “ ” position. VOLUME l6l8 20 24 28 34 40 50 60 70 l4 l2 l0 8 6 4 3 2 l 0 –dB 2 Turn the power on. POWER 3 * Select a desired input source. If you select turntable as an input source (PHONO position), you should confirm that the PHONO (MM/MC) switch is set to the position corresponding to the type of cartridge being used by the turntable. (Refer to page 9.) 4 * Select the speakers to be used. If you use two speaker systems, press both the A and B switches. SPEAKERS 5 Play the source. 6 Adjust to the desired output level. VOLUME l6l8 20 24 28 34 40 50 60 70 l4 l2 l0 8 6 4 3 2 l 0 –dB 7 If desired, adjust the BASS, TREBLE, BALANCE and LOUDNESS controls, etc. (Refer to page 8–9.) To turn off the power Press the POWER switch again. CD DIRECT AMPLIFIER Setting the INPUT SELECTOR to the CD position automatically sends the signals from the CD player (connected to the CD input terminals on the rear of this unit) to the built-in CD DIRECT AMPLIFIER specially developed for CD sound directly. CD sound is reproduced purely and clearly by this signal routing. English 1 TO RECORD A SOURCE TO TAPE (OR DUB FROM A TAPE TO ANOTHER) 1 Select the source to be recorded. REC OUT AUX 1 CD TUNER PHONO 2 TAPE COPY 1 2 2 Play the source. 3 Confirm the source by selecting it with the INPUT selector and turning up the VOLUME control. VOLUME l6l8 20 24 28 34 40 50 60 70 l4 l2 l0 8 6 4 3 2 l 0 –dB 4 Set the tape deck to be used for recording in the recording mode. 5 To monitor the sound to be recorded (or being recorded), select the tape deck being used for recording with the INPUT selector. Notes . If you want to enjoy another source while recording, select it with the INPUT selector. . The settings of VOLUME, BASS, TREBLE, BALANCE, LOUDNESS controls and PURE DIRECT switch have no effect on the material being recorded. REC OUT selector setting on tape dubbing To dub from tape deck 1 to tape deck 2 REC OUT AUX 1 CD TUNER PHONO 2 TAPE COPY 1 2 To dub from tape deck 2 to tape deck 1 REC OUT AUX 1 CD TUNER PHONO 2 TAPE COPY 1 2 3, 5 3 Adjusting the BALANCE control Selecting the SPEAKER system Adjust the balance of the output volume to the left and right Because one or two speaker systems can be connected to this speakers to compensate for sound imbalance caused from unit, the SPEAKERS switches allow you to select speaker speaker location or listening room conditions. system A or B, or both at once. BALANCE 0 l l 2 2 3 3 44 L5 5R Adjusting the BASS and TREBLE controls Adjusting the continuously variable LOUDNESS control BASS TREBLE BASS : Turn this clockwise to increase (or counterclockwise to decrease) the low frequency response. TREBLE : Turn this clockwise to increase (or counterclockwise to decrease) the high frequency response. SPEAKERS This control provides compensation for the human ears’ loss of sensitivity to high and low-frequency ranges at low volume. This control is adjustable to retain full tonal range at any volume level. 1 Set to the “FLAT” position. LOUDNESS 30 dB 0 9 8 7 6 2 Set to the loudest listening level that you would listen to. VOLUME l6 l8 l4 20 l2 24 l0 28 8 34 6 4 40 50 3 60 2 70 l 0 –dB 3 Turn until the desired volume is gained. LOUDNESS 30 dB 0 9 8 7 6 English Using the PURE DIRECT switch PHONO (MM/MC) switch You can enjoy the purest possible sound from your audio sources by setting thi...