Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Yamaha Dateigröße: 423.02 kb Dateiname: Unterrichtssprache:

REMOTE CONTROL (PHONO) connector AX-592 and AX-892 only If you have a YAMAHA turntable with a terminal for remote control, connect it to this connector using the cable provided with the turntable. This connection allows you to control the turntable with the remote control. REMOTE CONTROL PHONO REMOTE CONTROL PHONO (AX-592) (AX-892) PHONO (MM/MC) switch Select either MM or MC depending on your phono cartridge. If you use a high-output MC cartridge, select MM. To select MC, press the switch so that it stays in. To select MM, press the switch again, so that it releases. AX-592 and AX-892 only MM MC PRE OUT/MAIN IN terminals AX-592 and AX-892 only Removing the jumper pins enables this unit to independently perform the functions of a control amplifier and a power amplifier. These terminals are for connection of a signal- processing system such as a graphic equalizer or sound processor. If a sound processor or other external unit is connected between these terminals, the VOLUME control of this unit can be used for overall adjustment of the sound level. To connect such a unit, remove the jumper pins from the PRE OUT/MAIN IN terminals, connect the inputs of that unit to the PRE OUT terminals and its outputs to the MAIN IN terminals. For details, refer to the owner’s manual included with the unit to be connected. COUPLERPREOUT MAININ L R Note . If you will not use the PRE OUT/MAIN IN terminals, never remove the jumper pins. If removed, no sound will be output from this unit. . If you will use this unit with an external unit connected between the PRE OUT and MAIN IN terminals, make sure that the CD DIRECT AMP and PURE DIRECT switches on the front panel are turned off. . If you will use this unit as a power amplifier, connect the outputs of an external control amplifier, etc. to this unit’s MAIN IN terminals. In this case, this unit’s controls will not function, except the PHONES jack and the SPEAKERS switches, so use the controls on the external control amplifier to make volume adjustment, etc. English IMPEDANCE SELECTOR switch Make sure that the power to the unit is off, before you set the switch. Select the appropriate setting for your speaker system. Upper position 4 .: If you use either speaker system A or B, the impedance of each speaker must be 4 ., or higher. 8 .: If you use both speaker systems A and B at the same time, the impedance of each speaker must be 8 ., or higher. Lower position 6 .: If you use either speaker system A or B, the impedance of each speaker must be 6 ., or higher. 12 .:If you use both speaker systems A and B at the same time, the impedance of each speaker must be 12 ., or higher. VOLTAGE SELECTOR switch (General model only) If the pre-set setting is incorrect, set the switch to the proper voltage for your area. Consult your dealer if you are unsure of the correct setting. WARNING Be sure to unplug the unit before setting the VOLTAGE SELECTOR switch. 240V A OR B : 4. MIN. /SPEAKER A + B : 8. MIN. /SPEAKER A OR B : 6. MIN. /SPEAKER A + B :12. MIN. /SPEAKER WARNING Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged. IF THIS UNIT FAILS TO TURN ON WHEN THE POWER SWITCH IS PRESSED The IMPEDANCE SELECTOR switch may not be set to either end closely. If so, set the switch to either end closely. 12 CONTROLS AND THEIR FUNCTIONS FRONT PANEL NATURAL SOUND STEREO AMPLIFIER AX-492 PHONES INPUT VOLUME CD DIRECT AMP PURE DIRECT POWER SPEAKERS A ON OFF B BASS 1 2 3 4 – 5 1 2 3 4 5 + 0 LOUDNESS 1 2 3 4 5 -30db 10 9 8 7 FLAT 6 BALANCE 1 2 3 4 L 5 1 2 3 4 5 R 0 TREBLE 1 2 3 4 – 5 1 2 3 4 5 + 0 REC OUT CD TUNER PHONO TAPE 1 TAPE 2 (MD) AUX PHONO TUNER TAPE 2 (MD) AUX TAPE 1 CD -db 16 ° 0 60 2 40 4 28 8 20 12 2 3 1 E D C 4 5 6 8 9 0 A NATURAL SOUND STEREO AMPLIFIER AX-592 PHONES CD DIRECT AMP SPEAKERS A ON OFF B POWER INPUT VOLUME PURE DIRECT BASS 1 2 3 4 – 5 1 2 3 4 5 + 0 LOUDNESS 1 2 3 4 5 -30db 10 9 8 7 FLAT 6 BALANCE 1 2 3 4 L 5 1 2 3 4 5 R 0 TREBLE 1 2 3 4 – 5 1 2 3 4 5 + 0 REC OUT CD TUNER PHONO TAPE 1 TAPE 2 (MD) AUX PHONO TUNER TAPE 2 (MD) AUX TAPE 1 CD -db 16 ° 0 60 2 40 4 28 8 20 12 SUBSONIC FILTER ON OFF 2 3 1 E D 4 5 6 7 8 9 0 A C AX-492 AX-592 AAXX--889922 English E NATURAL SOUND STEREO AMPLIFIER AX-892 PHONES INPUT VOLUME CD DIRECT AMP PURE DIRECT SPEAKERS A ON OFF B POWER SUBSONIC FILTER ON OFF MUTING ON OFF BASS 1 2 3 4 – 5 1 2 3 4 5 + 0 LOUDNESS 1 2 3 4 5 -30db 10 9 8 7 FLAT BALANCE 1 2 3 4 L 5 1 2 3 4 5 R 0 TREBLE 1 2 3 4 – 5 1 2 3 4 5 + 0 REC OUT CD TUNER PHONO TAPE 1 TAPE 2 (MD) AUX PHONO TUNER TAPE 2 (MD) AUX TAPE 1 CD -db 16 0° 260 40 828 1220 231DBC 456789 0 A 1 Remote control sensor Receives signals from the remote control. 2 POWER switch Press this switch to turn the power on and off. When the power is on, the indicator will be illuminated. *Standby mode While the power is on, pressing the POWER key on the remote control switches the unit to the standby mode. (In this mode, the...

Herunterladen

Geben Sie zwei Ziffern: