Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
In this case, you must select whether to monitor the S video signal or the pin jack signal on the monitor TV side. Caution concerning use of S VIDEO connector Due to the circuit configuration of this unit, do not leave the S VIDEO connection cable plugged into the VCR2 S VIDEO OUT connector if the other end of the cable is not connected to the VCR component. 20 POWER CORDS 1. Connect the power cord of your tuner, cassette deck or other component to one of the two SWITCHED AC OUTLETS to automatically turn it on when the amplifier is turned on. The maximum total power consumption of the components connected to the SWITCHED AC OUTLETS must not exceed 100 watts. 2. Connect the power cord of your VCR or other unit to the UNSWITCHED AC OUTLET (U.S.A., Canada and general models only) to supply power to it constantly. The maximum power consumption of the unit connected to the UNSWiTCHED AC OUTLET must not exceed 200 watts. 3. Make sure that the power cords are not tied together with the input/output cables. 4. Connect the power cord of your amplifier to an AC outlet. 21 SURROUND PROGRAMS Dolby Pro Logic Surround The Dolby Pro Logic Surround system is designed for use with program material (mainly videotaped movie soundtracks) encoded with the Dolby Surround system. When playing these program sources, use this mode. Simulated Surround This mode is designed to enhance mono source programs. Since this mode creates a more expansive sound image, it can also be used to advantage with stereo programs. Compared to a strictly mono setting, the sound image createc in this mode is wider and slightly forward of the speaker pair, lending an immediacy to the overall sound. Live Surround This mode takes advantage of the delay signal and a feedback circuit for the rei surround speakers to create a bright, lingering, and somewhat resonant sound that characterizes a small concert space. Hall Surround In this mode, the center image seems to be located even more deeply behind th front main speaker pair, creating an expansive, large hall ambience. The apparent listening position is in the center of the hall rather than in front of the stage. PREPARATION FOF* THE BEST SURROUND CONDITION This preparation is important for proper Dolby Pro Logic Surround operation. ■ INPUT BALANCE AND FRONT MAIN/CENTER/REAR SURROUND SPEAKER BALANCE ADJUSTMENTS 1. Press the □□ PRO LOGIC button and then press the CENTER MODE button so that the CENTER MODE OFF indicator lights. 2. Use the input selector to select a component which can play a Dolby Surround encoded program and begin playback of the Dolby Surround encoded program. 3. While listening to spoken dialog, adjust the INPUT BAL control so that the dialog volume (heard from the left and right main and surround speakers) is reduced to the minimum level. (During normal operation, this dialog is reproduced from the center speaker.) 4. Select the Dolby Pro Logic mode with the CENTER MODE button. When using a 5-speaker system, press the CENTER MODE button so that the CENTER MODE NORM indicator lights. When using a 4-speaker system (i.e., no center speaker), press the CENTER MODE button so that the CENTER MODE PHANTOM indicator lights. 5. Press the TEST button. 6. Increase the volume level with the VOLUME UP key on the remote control transmitter. You will hear a test tone (pink noise) emitted from the front right main speaker, which then proceeds sequentially to the center speaker, the left main speaker, and then the rear surround speakers, for about two seconds each. • When using a 4-speaker system (Phantom mode), you will hear the center channel test tone from both the front left and front right main speakers. 7. Adjust the VOLUME control, CENTER LEVEL, and/or REAR LEVEL keys on the remote control transmitter so that the volume heard at the listening position is the same from each speaker. ® If you wish to adjust the relative volume levels of the left and right rear speakers, press the REAR BALANCE button and adjust the levels with the LEVEL/R.BAL/D.TIME buttons. Pressing the button shifts the sound image to the left. Pressing the ► button shifts the sound image to the right. 8. After completing this adjustment, press the TEST button again. NOTE: Once you have completed these adjustments, use only the VOLUME control of this unit. Do not change any other volume settings in the system. OPERATION PLAYBACK WITH SURROUND MODE 1. Turn on the power of all components to be used in the system. 2. Select a Surround Mode. With Dolby Surround Press the aa PRO LOGIC button and then select the center mode with the CENTER MODE button. When using a 5-speaker system, press the CENTER MODE button so that the CENTER MODE NORM indicator lights. When using a 4-speaker system, press the CENTER MODE button so that the CENTER MODE PHANTOM indicator lights. With another Surround Mode (SIMULATED SURROUND, LIVE, or HALL) Press the SIMULATED SURROUND button, LIVE button, or HALL button ac...