Login:
Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Anleitung Yamaha, modell RS500

Hersteller: Yamaha
Dateigröße: 2.87 mb
Dateiname:
Unterrichtssprache:
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Dieses Gerät hat auch andere Anweisungen:

Anleitung Zusammenfassung


2. With the rack standing up, loosen the bolts q located on the left and rotate the left leg towards you until it is positioned as shown in Figure 1 Top view. • The bolts q can be found on the rear of the clamp on the left pillar. 3. Loosen the bolts w located on the right in Figure 2 and rotate the right leg clockwise from the left until it comes fully around as shown in Figure 2 Top view. • The bolts w can be found on the rear of the clamp on the right pillar. 4. Tighten the bolts loosened in Steps 2 and 3 above. Setting up RS500 Bolts q [Figure 1] Right leg Left pillar Left leg Drum trigger module clamp 2 2 [Figure 1 Top view] Left leg Right leg Left pillar Right pillar 2 Right pillar [Figure 2] Bolts w Left leg Right leg Right pillar Left pillar 3 Drum trigger module clamp [Figure 2 Top view] Left leg Right leg Left pillar Right pillar 3 CAUTION • The rack may topple over and cause injury if the left and right legs are opened any wider than shown in the figure below. You should not, therefore, exceed the dimensions indicated. 5. Loosen the bolt r, and as shown in Figure 3, raise up the cymbal holder located on the left. Following this, retighten the bolt r. •When tightening the bolt, ensure that the black sleeve is positioned inside the clamp’s mounting hole. 6. Loosen the bolts t, and as shown in Figure 3, rotate upward the cymbal holder located on the right. Following this, retighten the bolts t. 7. Loosen the bolts e and open up the pipe q to position it as shown in Figure 3. Then, rotate the snare clamp rod to the position shown in Figure 3. Retighten the bolts e. 8. Loosen the bolts of the tom holders and rotate the three tom holders into the positions shown in Figure 3. Then, retighten the bolts. [Figure 3: Example of standard assembly] Bolts eTom holder Tom holder Left leg Right leg Drum trigger module clamp Right pillar Left pillar Cymbal holder Cymbal holder Snare clamp rod Bolts rBolts tBolts Pipe qBolts y5 6 7 8 8888 9 CAUTION • Take special care when handling the tom holders in order to avoid injuring yourself with their sharp ends. 9. Loosen the bolts y securing the drum trigger module clamp in place, position the clamp with its flat surface facing upward, and then retighten the bolts y. For information about the next steps such as assembling Yamaha Electronic Drum Set, refer to “Assembly Manual” in the Pad Set. Specifications . External dimensions: 1196 (W) x 528.3 (D) x 812.3 (H) mm (Standard Assembly) . Weight: 11 kg * Specifications and descriptions in this Owner’s Manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. RS500/RS700 Owner’s Manual 3 4 RS500/RS700 Owner’s Manual 1. Remove the rack from its box and stand it up with the drum trigger module clamp positioned on the right as shown in Figure 1. 2. ...

Dieses Handbuch ist für folgende Modelle:
Musikinstrumente - DTX RS500 (2.86 mb)
Musikinstrumente - DTX RS700 (2.86 mb)
Musikinstrumente - RS700 (2.87 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien