Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc. • Do not push or scrape the playing surface of your pad with drum sticks as this may make it less sensitive and/or more difficult to play. 4 PCY90AT Owner’s Manual Welcome First of all, thank you for purchasing the Yamaha PCY90AT—a drum pad designed primarily for use as a cymbal with products from the DTX series of Yamaha electronic drum sets. In order to get the most out of your new accessory, please be sure to read this owner’s manual carefully. And after doing so, be sure to store the manual in a safe place so that you can refer back to it again as needed. Package Contents q Cymbal pad (.1) w Stopper (x1) e Cymbal holder (x1) r Stereo audio cable (.1) t Owner’s Manual (x1; this booklet) qrwte PCY90AT Owner’s Manual 5 Setting Up As shown in the figures, set up your cymbal pad on an electronic drum rack. CAUTION If the clamp bolts and other fasteners are not sufficiently tightened, your pad unit may fall, possibly causing injury. It is important, therefore, that you mount your pad unit securely on the drum rack. In addition, you should avoid placing your rack on an uneven surface as this may cause it to fall over, again increasing the risk of injury. .Attaching the cymbal holder 1. Take the cymbal holder from the package and loosen the clamp bolts. (See Figure 1.) 2. Slide the holder clamp onto the electronic drum rack as shown by the arrow below. (See Figure 2.) Cymbal holder Clamp bolts Figure 1 Holder clamp Figure 2 3. Tighten the clamp bolts to secure the cymbal holder in place. 6 PCY90AT Owner’s Manual .. 1. Using a tuning key (sold separately), loosen the stopper’s key bolt. (See Figure 1.) 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. (See Figure 2.) 3. Slide the stopper onto the cymbal holder. (See Figure 3.) If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to slide the stopper onto the cymbal holder’s shaft. In such a case, loosen the key bolt as much as possible without removing it. 4. Replace the bolt cover. (See Figure 3.) When assembling the bolt cover, turn it until it stops. Figure 1 Figure 2 Figure 3 Stopper Key bolt Tuning key (sold separately) Wing nut Felt pads Bolt cover Cymbal holder Bolt cover Stopper Cymbal holder 5. Secure the stopper in place. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper’s key bolt using the tuning key. (See Figure 4.) Bolt cover Full contact Stopper Figure 4 6. Place one of the felt pads removed in Step 2 on the cymbal holder. (See Figure 5.) 7. Assemble the pad on the cymbal holder. Lower the pad into place with the cymbal holder’s shaft passing through the hole at the center of the cup. When mounted, the stopper’s pin should rest inside the pad’s smaller hole. (See Figure 5.) If the stopper’s pin is not positioned fully inside the smaller hole, the pad could become free of the stopper when played. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. 8. Place the second felt pad removed in Step 2 on the cymbal holder. (See Figure 5.) PCY90AT Owner’s Manual 7 9. Tighten the wing nut to secure the pad to the cymbal holder. (See Figure 5.) Wing nut Figure 5 Cup Felt pad Pad Felt pad Bolt cover Cymbal holder Stopper Stopper Cup Pad Smaller hole Pin Pads and Trigger Input Jacks The functions that the pad can perform will depend on which of your drum module’s trigger input jacks it is connected to. A chart showing the correspondence between pad functionality and input jack types can be accessed via the web page shown below. 8 PCY90AT Owner’s Manual Connecting Using the stereo audio cable provided, connect the cymbal pad’s output to a suitable input jack on your DTX series drum module. At this time, ensure that the L-shaped end of the cable is plugged into the pad’s [OUTPUT] jack. Cymbal pad DTX series drum module Troubleshooting If the pad produces no sound, proceed as follows. • Ensure that the pad is correctly connected to a suitable input jack on your DTX series drum module using the stereo audio cable provided. For more troubleshooting tips, refer to the Owner’s Manual that came with your DTX series drum module. If you still cannot find the information you need to resolve a problem, please contact your Yamaha dealer or a customer support center for assistance. Specifications . PCY90AT • External dimensions: 254 x 254 x 480 mm • Weight: 1.0 kg • Sensor System: Trigger sensor (piezo) x 1 • Output jack: Standard mono-audio jack *: Specifications and descriptions in this Owner’s Manual are for information purposes only. Yamaha Corporation reserves the right to change or modify products or specifications a...