Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury. WARNING If this symbol is ignored and the equipment is used improperly, there is a danger or injury to persons handling the equipment, and material damage could occur. • Watch your fingers when adjusting clamps. They may become pinched, resulting in injury. • Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers. • Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury. • Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. CAUTION Assembling the Rack System For details, refer to the Assembly Manual of the RS130. Checking the contents of each package Mounting the Pads and the Drum Trigger Module on the Rack System Mount the Pads and the Trigger Module on the Rack System. Then position the Kick Pad and the Hi-Hat. 1 2 Package 1 [DTP900] . PCY135 (Cymbal Pad) (2) . PCY155 (Cymbal Pad) (1) . RHH135 (Real Hi-Hat Pad) (1) . KP125W (Kick Pad) (1) . CH750 (Cymbal Holder) (2) . SS662 (Snare Stand) (1) . Stand base for the RHH135 (1) . Hi-Hat clutch for the RHH135 (1) . Cable band for the RHH135 (1) . Stoppers for the PCY135/155 (3) . Felts for the PCY135/155 (3) . 2.5m stereo phone cables (7) . 4m stereo phone cables (4) . Cable bands (10) . 2m spiral tube (1) * You can cut this tube to any desired length and use it in order to take up any slack of the cables. . Owner’s Manuals (for each Pad) • PCY65/65S/135/155 • KP125W • RHH135 . Tuning key (1) Package 3 [Drum Trigger Module DTX900] . Drum Trigger Module DTX900 (1) . Module stand fastening screws (4) . Module Stand (1) . AC Power Adaptor (1) . DTX900 Owner’s Manual (1) . DTX900 Data List (1) Package 2 [DTP901] . XP100T (Tom Pad) (3) . Clamp bolt (3) . CH755 (Cymbal Holder) (1) . HS740A (Hi-Hat Stand) (1) . XP120SD (Snare Pad) (1) . Additional holder clamp (1) . XP100T/100SD/120T/120SD Owner’s Manual (1) . Assembly Manual (this sheet, 1) 3 1. Remove the right end support (shown below with a) of the Rack, attach the additional Holder Clamp in the direction shown below, then attach the support to the Rack again. 2. Attach the Cymbal Holders (CH750 x 2 and CH755 x 1) to the Rack System as shown below. Attaching additional Holder Clamps and Cymbal Holders CH750 CH750 CH755 Additional Holder Clamp a Loosen the screws. 1. Attach the clamp bolt then tighten it with five or six turns on each of three Tom Pads. 2. Attach three Tom Pads to the clamp rods on the rack respectively. As shown below, attach the Tom Pad to the rod part so that the rod part is to be inserted to the hole of the Tom Pad, then tighten the clamp bolt firmly. 3. If you want to change the location (height and angle) of the Tom Pad, use the clamp bolts A and B. Loosen the one of the clamp bolts, adjust the location of the Pad, then make sure to tighten the clamp bolts again before adjusting another clamp bolt. Attaching the Tom Pad XP100T Clamp bolt (to be tightened as shown) Tom pad (back side) Clamp rod Clamp bolt To be inserted Rod parts Tom pad Clamp bolt A Clamp bolt B Continued on the next page (on the back side) U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation ©2009 Yamaha Corporation WT59070 910PO***.*01A0 Printed in Japan 1. Remove the wing nut and the two felt washers from the Cymbal Holder. Then turn the tilter sleeve in a counterclockwise direction and remove it. 2. Attach the stopper to the Cymbal Holder, and fix at a position where the L-shaped part of the stopper is on the opposite side from you. To fix the position of the stopper, use the tuning key and tighten the key bolt firmly. 3. Attach the tilter sleeve removed in step 1 to the Cymbal Holder again, and tighten it in a clockwise direction. 4. Attach one of the felt washers removed in step 1 to the Cymbal Holder. The other felt washer will not be used within the standard assembly described in this manual. 5. Insert the end of the L-shaped part of the stopper into the oval-shaped hole (shown as a) on the Cymbal Pad to set the Pad on the Holder. * Cymbal Pad PCY135 is very similar to Real High- Hat Pad RHH135. Check the model name on the reverse side. 6. Attach the included round-shaped felt with a large hole-diameter to the Cymbal Holder, then attach the wing nut removed in step 1 and tighten it. Turn the wing nut until you are certain that the Cymbal Pad is attached. The Cymbal Pad is designed to shake when you hit the surface, even when the wing nut is tightened securely. Attaching the Cymbal Pad PCY135 PCY135 PCY155 Cymbal holder Wing nut Felt washer Tilter sleeve Tuning key Key bolt Stopper Felt washer Tilter sleeve Felt washer supplied with the Cymbal Pad a Wing nut 1. Attach the included module stand to the back side of the Drum Trigger Module by using the module stand fastening screws. 2. Attach the module stand onto the holder clamp, then tighten...