Login:
Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Anleitung Yamaha, modell DTX700K

Hersteller: Yamaha
Dateigröße: 2.6 mb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Dieses Gerät hat auch andere Anweisungen:

Anleitung Zusammenfassung


2. Mount the three tom pads on the rack’s clamp rods. As shown below, ensure that the rod section is fully inserted into each pad’s mounting hole, and then fully tighten the clamp bolt. 3. If necessary, use clamp bolts A to D to adjust the height and angle of any of the pads. When doing so, be sure to adjust one bolt at a time (i.e., loosen a bolt, adjust the pad, and then retighten before loosening another). XP80 XP70 Clamp bolt (to be tightened in the direction shown) Snare pad (rear side) Insert Snare pad Rod section Clamp rod Clamp bolt Clamp bolt A Clamp bolt C Clamp bolt E Clamp bolt D Clamp bolt B Tom pad Clamp bolt Insert Rod section Clamp rod Clamp bolt C Clamp bolt D Clamp bolt B Clamp bolt A Continued on other side Mounting the drum trigger module and cymbal pads . Mounting the drum trigger module 1. Attach the module stand (provided) to the underside of the drum trigger module using the module stand fastening screws. 2. Place the module stand inside the holder clamp and tighten the clamp bolt to secure in position. . Mounting the cymbal pads 1. Using a tuning key, loosen the stopper’s key bolt. 2. Remove the wing nut, the two felt pads, and the bolt cover from the cymbal holder. 3. Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder’s shaft. In such a case, loosen the key bolt as much as possible without removing it. 4. Replace the bolt cover. * When assembling the bolt cover, turn until it no longer rotates. 5. Secure the stopper in place. With the stopper making full contact with the bottom surface of the bolt cover, tighten the stopper’s key bolt using a tuning key. 6. Place one of the felt pads removed in Step 2 on the cymbal holder. 7. Mount the pad unit on the cymbal stand. Lower the pad unit into place with the cymbal holder’s shaft passing through the central hole of the cup section. When mounted, the stopper’s pin should rest inside the pad unit’s smaller hole. * If you were to play a cymbal pad without the stopper’s pin positioned inside the smaller hole, the pad could rotate, causing the cable to be pulled out. It is very important, therefore, to ensure that the stopper is secured as described in Step 5 above. 8. Assemble the felt pad that came with your pad unit. * The second felt pad removed from the cymbal holder in Step 2 above is not required for assembly of your pad unit. 9. Tighten the wing nut to secure the pad unit to the cymbal holder. PCY135 PCY135 Drum trigger module Module stand fastening screws Module stand Drum trigger module (back side) Front of module Clamp bolt Drum trigger module + module stand Insert Holder clamp Tuning key Key bolt Stopper Cymbal holder Felt pads Bolt cover Wing nut Cymbal holder Stopper Bolt cover Cymbal holder Stopper Bolt cover Full contact Pad unit Felt pad that came with pad unit Cymbal holder Felt pad Bolt cover Pad unit Stopper Pin Wing nut Stopper’s pin Smaller hole Assembling the hi-hat stand 1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the floor to protect it from scratching. 2. Loosen the hi-hat stand’s wing bolt (a in the following figure). 3. Extend the tripod legs to stabilize the stand. Retighten the wing bolt loosened in Step 2. 4. Insert the radius rod into the frame hole as shown below. 5. As shown on the right, loosen the wing bolt (b in the figure) to remove the hi-hat clutch. * This hi-hat clutch is not used within the standard assembly example shown in this pamphlet. Instead, use the hi-hat clutch that came with your RHH135. 6. Pull out the hi-hat shaft from the upper pipe . 7. Screw the hi-hat shaft into the nut on the lower pipe . 8. Insert the upper pipe into the hi-hat shaft from above, and then tighten the wing bolt (c in the figure) with the support plate positioned at the middle area of the hi-hat shaft . 9. Remove the felt washer located above the support plate. It is not used within the standard assembly example shown in this pamphlet. 10. Set up the RHH135 Real Hi-hat Pad. * Refer to refer to the Setting Up section of the owner’s manual that came with your RHH135. Radius rod Wing bolt a Radius rod Felt washer Hi-hat clutch Support plate Support plate c b Position the hi-hat stand and kick pad as desired, referring to the standard assembly example on the other side. Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard boxes on the floor under the hi-hat stand and kick pad to protect it from damage. Connect the pads to the drum trigger module. As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module. Connect the drum trigger module to a power supply. This completes the assembly procedure. * For information about tuning the power on/off, checking the actual sound, and other subsequent steps, refer to the Setting Up section of the owner...


Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien