Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
• The AUTO-SENS function can be operated from the control panel. • The latency with ASIO has been reduced even further. • The operating sample rate can be changed from within your DAW application. Operating Requirements In order to use OCTA-CAPTURE Version 1.5, you’ll need to update the driver and the system program. OCTA-CAPTURE System program Ver. 1.50 or later Driver Ver. 1.5 or later In order to use the OCTA-CAPTURE as an expansion device for the VS-100 or VS-700, the driver of the VS-100 or VS-700 must be updated. VS-100 Windows driver Ver.2.0.1 MacOS 10.7: Ver. 1.0.0 Mac driver MacOS 10.6: Ver. 2.0.0 MacOS 10.5: Ver. 2.0.0 VS-700 Windows driver Mac driver Ver. 2.0.1 Ver. 1.0 Copyright © 2011 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Roland is a registered trademark of Roland Corporation in the United States and/or other countries. Updating the System Program Checking the Version Please check the OCTA-CAPTURE’s system software version. When you turn the power on, the system software version is shown in the lower middle of the screen. If a version earlier than V1.50 is indicated An update is required. Please perform the update as described below. If V1.50 or later is indicated No update is required. Updating 1. Disconnect the USB cable. 2. While simultaneously holding down the [ ] button in the OCTA-CAPTURE’s PRE-AMP control section and pressing the [CURSOR/VALUE] knob, turn the power on. Continue holding down the button and the knob until the following screen appears. 3. Use the USB cable to connect the OCTA-CAPTURE to your computer. When the USB connection is detected, the following screen will appear. Your computer will recognize the OCTA-CAPTURE as a removable disk. 4. Drag (copy) UpdOcta.dat onto the removable disk. 5. When you see that the copy has been completed, disconnect the USB cable. After you disconnect the USB cable, the program will start being written. NOTE Do not power off the OCTA-CAPTURE until the update is complete, doing so may damage the unit. A screen like the following will appear. When the program has been updated successfully, the screen will show the updated version. This completes the update procedure. Updating the System Program Checking the Update 6. Turn the power of the OCTA-CAPTURE off, then on again. Make sure that V1.50 or later is now shown as the system software version in the bottom of the screen. * If the update was unsuccessful, you can retry the process from step 1. Updating the OCTA-CAPTURE Driver Installing the Driver The downloaded file is a ZIP format archive file. Right-click the file’s icon, and choose “Extract all” to extract the files as directed in the screen. For details on the installation procedure, refer to the Readme.htm file that is created when you extract the archive. * Uninstall the old driver before you install the new driver. For details on the uninstallation procedure, refer to the Readme.htm file that was created when you extracted the archive. Be sure to read the Readme.htm (*) file before you install the driver. Version 1.5 Functions Direct Mixers and Routing In addition to its audio interface, the OCTA-CAPTURE internally provides four direct mixers (p. 7) and a patch bay (p. 11). Settings for these can be made using the OCTA-CAPTURE’s own knobs and buttons (p. 14), as well as from your computer using a dedicated control panel. Direct Mixer A, B, C, D This allows the input signals to be directly output for monitoring without being routed through the computer. You can adjust the balance among these signals and the playback from the computer. The direct mixer is a stereo mixer that provides individual adjustment of volume and pan for each input and each playback channel from the computer. You can control the four mixers independently. For details, refer to “Direct Mixer control” (p. 7). PATCH BAY This allows you to assign the output destinations of the four direct mixers and the output destinations of the playback channels from the computer. For details, refer to “Patch Bay” (p. 11). Direct mixer A–D OUTPUT 1–2 OUTPUT 3–4 OUTPUT 5–6 OUTPUT 7–8 OUTPUT 9–10 PHONESPATCH BAY INPUT 1–10 WAVE IN WAVE OUT 1–10 1–10 1–10 1–8 11–12 1–10 Headphone Jack COAXIAL output jack Output Jacks 3–4 Output Jacks 5–6 Output Jacks 7–8 Input jacks Main output jacks 1–2 Direct Mixer A Master Input Mixer A Output Mixer A 1–2 Reverb Mixer A only OCTA-CAPTURE Control Panel A B C D If you want to fully control the OCTA-CAPTURE’s direct mixer and patch bay, it’s convenient to use the dedicated OCTA-CAPTURE control panel (p. 5). In addition to the direct mixer and patch bay, this allows graphic editing of the OCTA-CAPTURE’s preamps and compressors as well. Let’s try using the direct mixer while using the control panel. Control Panel The OCTA-CAPTURE’s control panel controls the OCTA-CAPTURE’s internal preamps, the four direct mixers, and the patch bay. The control...