Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
When you are ready, press [F2 (STEP)] to proceed to the next set of parameters until the entire setup is complete. Step Editing can help you learn how the VS-1824 works and is therefore a great tool for beginners. When you have finished your setup, you can save it as an EZ Routing template. The following pages describe how to use EZ Routing Step Editing. Setting Up for Recording Using Step Editing Select this when you want to make a new recording from a source connected to one of the INPUT jacks. If you wish to cancel the settings procedure, press [F6 (EXIT)]. 1. Press [EZ ROUTING]. The EZ Routing icon appears in the display. 2. Press [F5 (Exec)]. If “Exec” does not appear in the display above [F5], press [PAGE] until you see “Exec,” and then press [F5 (Exec)]. 3. Press [F1 (Rec)]. 4. Specify which input source is to be recorded to each track. To do this, first press the Input SELECT for the input you want to use, then press the Track STATUS button for the track you want to record on. Using this method, you can assign a single Input to two different tracks for recording. Use [ ] and [ ] to move the cursor and the TIME/VALUE dial to select the V-Track on which you want to record. Source assigned to the MIX bus 5. Press [F2 (STEP >)]. 6.Only the source and destination channels you specified during Step 4 will be shown. Use [ ], [ ], [ ], and [ ] to move the cursor and the TIME/VALUE dial to adjust each of the values. * You cannot assign a DIGITAL input to more than one stereo- linked pair of tracks. * Using EZ Routing, it is not possible to assign a stereo-linked input to tracks that are not linked. For example, to record the DIGITAL input on Tracks 3 and 4, you must first turn Channel Link on for Track 3. Source assigned to the track Source Track V-Track Cursor 7. Press [F2 (STEP >)]. You can return to the previous screen by pressing [[F1 (STEP<)]. Pan/Balance Level Output destination (MIX us or track) Chapter 8 EZ Routing 8. Make the settings for the effects. Use [ ], [ ], [ ], and [ ] to move the cursor and the TIME/VALUE dial to adjust each of the values. Press [F3 (FX A)] to make settings to EFFECT A (FX1/2); press [F4 (FX B)] to make settings to EFFECT B (FX3/4). Cursor Effect Switch Send Level Send Balance 9. Press F2 (STEP >)]. You can return to the previous screen by pressing [F1 (STEP<)]. 10. Decide whether or not to record the output of each effect to a track. First, press the Effect SELECT button for Effect 1 or Effect 2, then press the STATUS button for the track you want the effect recorded on. To select FX 3 or FX 4, hold [SHIFT] and press the Effect SELECT button. Tracl to be recorded 11. Press [F2 (STEP >)]. You can return to the previous screen by pressing [F1 (STEP<)]. 12. Select mixer channels to be output to the AUX bus. The AUX bus is useful for creating a separate headphone mix for the performer you are recording. Use [ ], [ ], [ ], and [ ] to move the cursor and the TIME/VALUE dial to adjust each of the values. AUX Switch AUX Send Switch AUX Send Pan/Balance Cursor 13. Press [F2 (STEP >)]. You can return to the previous screen by pressing [F1 (STEP<)]. 14. Select the Master Section settings. Use [ ], [ ], [ ], and [ ] to move the cursor and the TIME/VALUE dial to adjust each of the values. Monitor Select Equalizer Mode Direct Out Effect Insert 15. Press [F4 (Exec)]. “EZ ROUTING Step Edit is finished!!” appears in the display. WARNING: EZ Routing settings will override any existing mixer settings you have already made. 16. You can save your setup as an EZ Routing template, or Exit [F6 (EXIT)] to leave this display without saving. To save the setup, press [F3 (SAVE)]. The Routing Save screen appears in the display. Save the setup using the procedure described in “Saving an EZ Routing Template,” p. 123. Chapter 115 Chapter 8 EZ Routing Setting Up for Mixing Using Step Editing Select this when you want to adjust the balance of each track, or to mix your song to an external two-track recorder. Select this to use the Input Mixer during mixdown to mix external sources along with your 18 tracks to the VS-1824’s stereo MASTER mix outputs. If you want to cancel the settings procedure before completing it, press [F6 (EXIT)] at any time. 1. Press [EZ ROUTING]. The EZ Routing icon appears in the display. 2. Press [F5 (Exec)]. If “Exec” does not appear in the display above [F5], press [PAGE] until you see “Exec,” and then press [F5 (Exec)]. 3. Press [F2 (Mix)]. 4.Specify which sources are to be output to the MIX bus. Press the Input SELECT buttons and the Track SELECT buttons for all mixer channels you want to include. Use [ ] and [ ] to move the cursor and the TIME/ VALUE dial to select the V-Track you want to play back. Source assigned to the MIX bus Source Track V-Track Track assigned to the MIX bus 5. Press [F2 (STEP >)]. 6. Only the sources—Input Mixer Channels and Track Mixer Channels—you specified during Step 4 will be shown. Use [ ], [ ], [ ], and [ ] to move the cursor and the TIME/VALUE di...