Stimmen - 2, Durchschnittliche Bewertung: 4 ( )

Hersteller: Roland Dateigröße: 7.43 mb Dateiname: Unterrichtssprache:

The functions appear in the display. 3. Press [F4] (DEL). 4. Rotate the VALUE dial to select the Library number to be deleted. 5. Press [ENTER/YES] two times. 53 ■ SCENE MEMORY Selecting the SCENE BANK while viewing the names 1. Press [BANK]. 2. Rotate the VALUE dial to select a SCENE BANK number. 3. Press [ENTER/YES]. To set a SCENE so that only the specified parameters to be reflected in the mix 1. Press [BANK]. 2. Press [FI] (PREF). 3. Press [ T ] to select "ItemSelect." 4. Use the [ T ], [ I ], [ <- ], and [ X ] buttons to select the parameters to be reflected in the SCENE recall. 5. Rotate the VALUE dial to place a check mark in the box. Fader — affects the volume settings Pan — affects the pan settings EQ — affects the equalizer settings Routing — affects the input and output routing Send Level — affects the send levels to the effects and AUX Effects — affects the effect settings Compressor — affects the compressor settings To get a SCENE to apply a smooth transition between track volumes when a scene is recalled (fade-in or fade out) 1. Press [BANK], 2. Press [FI] (PREF). 3. Press [ I ] to select "Trans.Speed." 4. Rotate the VALUE dial to set the length of time during which the volume will change in each channel when a SCENE is switched. Naming a BANK 1. Select the BANK to be named (hold down [BANK] and press [SCENE3] or [SCENE4]). 2. Press [BANK]. 3. Press [F1-F4 ON/OFF). The functions appear in the display. 4. Press [FI] (NAME). 5. Use the [ <— ] and [ -» ] buttons and the VALUE dial to set the Name. * By pressing IF11 (Ins), you can insert one character at the cursor position; press [F2] (Del) to delete one character at the cursor position. 6. Press [ENTER/YES] two times. Alternatively, you can press [F4] (EXEC) followed by [ENTER/YES], Copying the content of one SCENE to another SCENE 1. Press [BANK], 2. Press [F1-F4 ON/OFF]. The functions appear in the display. 3. Press [F2] (COPY). 4. Press I «— 1 to select "Source." 5. Rotate the VALUE dial to select the copy source BANK/ SCENE number. 6. Press [ -» ] to select "To." 7. Rotate the VALUE dial to select the copy destination BANK/SCENE number. 8. Press [F4] (EXEC) (When the message "Are You SURE?" appears in the display, press [ENTER/YES]). Exchanging the content of one SCENE with that of another SCENE 1. Press [BANK], 2. Press [F1-F4 ON1/OFF]. The functions appear in the display. 3. Press [F3] (SWAP). 4. Press [ <- ] to select "Source." 5. Rotate the VALUE dial to select the swap source BANK/ SCENE number. 6t Press ! —> ] to select "To." 7. Rotate the VALUE dial to select the swap destination BANK/SCENE number. 8. Press [F4] (EXEC), then press [ENTER/YES]. Undoing and redoing a SCENE This changes the mixer settings back to their condition prior to thr UNDO of the SCENE (undoes the undo). 1. Hold down [SHIFT] and press [ENTER/YES] (REDO). 2. The "u" mark disappears from "BANK/SCENE" in the display. ■ SOLO MODE (Monitoring Only Specified Channels) Selecting the channel to be monitored 1. Press [SOLO], 2. Press [SELECT] for the channel you want to monitor. The buttons inlight flashes. 3. Press [SOLO] once more. Switching Solo mode 1. Hold down [SOLO]. The "SOLO MODE" screen appears in the display. Continue to hold down the button. 2. Rotate the VALUE dial or press one of the buttons [F1]-[F4[ to select the Solo mode. "PRE EQ" "POST EQ" "AFL" (After Fader Listen) "IN PLACE" 3> Release the [SOLO] button. * When in Solo mode, select "MIX" (MIX BUS) as the signals being output from MONITOR (headphones). If set to something other than “MIX," the sound cannot be beared from the MONITOR (headphone) jack. * When "IN PLACE" is selected, "Soloed" channels are also output from MASTER OUT (the sounds from MONITOR and MASTER OUT are the same). Releasing Solo mode from all channels 1. Hold down [SHIFT] and press [SOLO]. ■ CHANNELS/FADERS Selecting the channel for which the parameters are to be set 1. Press [SELECT] for the channel whose parameters you want to adjust. Checking each channel's parameter settings 1. Press [LEVEL METER]. 2. Press [F2] (CH VIEW). The settings for the currently selected channel appear in the display. Adjusting the pan (balance) and other settings while viewing all of a channel's settings 1. Press [LEVEL METER]. 2. Press [SELECT] for the channel to be adjusted. 3. Adjust the values for the parameters below with knobs [ VI ]-[ V4 ]. [VI] — Pan (Balance when Stereo Link is in effect) [V2] — EFFECT 1 send level 54 [V3] — EFFECT 2 send level (VM-3100Pro only) IV4] — Send level to Internal bus 1 /2. (When the knob icon is displayed.) Adjusting the volum...

Herunterladen

Geben Sie zwei Ziffern: