Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
It corresponds to the sound of the "head-side" of the connected trigger input. — L Edge Sho MB ■M—Bi I This playing method involves striking the edge of the hi-hat with the shoulder of the stick. When played as showm in the figure, the "rim-side" sound of the connected trigger input is triggered. Position the "Roland" logo on the farther side, as viewed from the player (p. 5). Size: 12 inches Trigger: 2 (Bow/Edge) Connectors: TRIGGER OUT Jack CONTROL OUT Jack Dimensions: 314 ( W) x 314 (D) x 154 (H) mm 12-3/8 (W) x 12-3/8 (D) x 6-1/16 (H) inches Weight: 1.7 kg / 3 lbs 12 oz Options: Owner's Manual, Connection Cable, Tuning Key, Cable Tie, Insulating Plate * In the interest of product improvement, the specifications and/ or appearance of this unit are subject to change zvithout prior notice. Compatible Stand 9 Troubleshooting No sound is heard Is the TRIGGER OUT connected to the sound module's HH CTRL jack? Connect the VH-ll's TRIGGER OUT jack to the sound module's HI-HAT jack, and the CONTROL OUT to the sound module^ HH CTRL (p. 6). The sound does not change when an edge shot is made Is a monaural cable being used? When a monaural cable is used, the sound does not change when an edge shot is made. Use a stereo (TRS) cable. Are you striking the area where an edge sensor is located? The VH-11 has an edge sensor only at the area closest to you, at the front (p. 9). Position the "Roland'' logo on the farther side, as viewred from the player (p. 5). Foot splashes difficult to produce If you are using the TD-12/20 as your sound module, adjust the "Foot Splash Sens." If you are using the TD-10/8/6V/6 or other sound module, adjust the VH-ll's offset, the stand, the hi-hat clearance, and/ or the pedal spring tension until the foot splash sound is easy to produce. Sounds cut out Have you adjusted the VH-11 's offset? Adjust the offset by rotating the VH-ll/s VH offset adjustment screw (p. 7, p. 8). • Sounds may cut out when the hi-hat is struck forcefully if the screw is turned too far in the "CLOSE" direction. • The offset may change somewhat as you perform. • Your particular stand may require even further adjustment. Unable to control opening and closing Have you adjusted the VH-11 's offset? Adjust the offset by rotating the VH-ll's VH offset adjustment screw-7 (p. 7, p. 8). • The VH-ll's offset needs to be adjusted to ensure proper expression of the hi-hat's opening and closing. Adjust until you are satisfied with the correspondence between the hi-hat's opening and closing action and the change in tone. • The offset may change somewhat as you perform. • Your particular stand may require even further adjustment. Is the sound module set correctly? If you are using a TD-12 or TD-20, confirm the sound module's settings. • If you have the TD-12 sound module connected —> p. 7 ® If you have the TD-20 sound module connected —» p. 8 Is the hi-hat open when turning on the power? When using the TD-10+TDW-1, TD-8, and TD-6V/6, turning on the powder to the sound module with the hi-hat in the closed position may cause faulty operation. Sounds are not triggering properly Is the trigger type set correctly? Make the trigger parameter settings for your sound module (p. 6, p. 8). Is the direction of the hi-hat correct? Position the "Roland" logo on the farther side, as viewed from the player (p. 5). Are you using the special VH-11 dutcn? Clutches included with hi-hat stands are shaped differently than the VH-ll's special clutch, so use of such other clutches prevent the sensors within the VH-11 from functioning properly. Be sure to use the clutch designed especially for the VH-11. 10 If the Clutch Was Apart from the Hi-Hat If the hi-hat clutch is inadvertently removed from the hi-hat, use the following procedure to reassemble and attach the clutch. Due to the different shape, the clutch included with the hi-hat stand cannot be used with the VH-11. Be sure to use the special VH-11 clutch. Clutch Top -r.- - -- VH Offset Adjustment Screw —mm Plastic Washer- Rubber Washer-fc.,- Stopper (Lower) - --Set the screw to front. * Orient the stopper (upper) so that it matches the groove in the hi-hat. Hi-Hat Being Properly Assembled 4r * Player Side The upper end of the screw pipe of the stopper can be seen The VH offset adjustment screw being fully tightened 11 Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. (AFRICA) EGYPT A1 Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD El Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 REUNION Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP79 9 7 491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429 SOUTH AFRICA That Other Music Shop(PTY)Ltd. 11 Melle St., Braamfontein, Johannesbourg, SOUTH AFRICA TEL: (011)403 4105 FAX: (011)403 1234 Paul Bothner(FTY)Ltd. 17 Werdmuller Centre, Main Ro...