Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
The sound can be unmusical and lack distinctive pitches. Parameter/ Range Explanation MODE This selects the mode for the ring modulator. NORMAL This is a normal ring modulator. INTELLIGENT By ring-modulating the input signal, a bell like sound is created. The intelligent ring modulator changes the oscillation frequency according to the pitch of the input sound and therefore produces a sound with the sense of pitch, which is quite different from the NORMAL setting. This effect does not give a satisfactory result if the pitch of the bass sound is not correctly detected. So, you must use single notes, not chords. FREQ (Frequency) 0–100 Adjusts the frequency of the internal oscillator. EFFECT LEVEL 0–100 Adjusts the volume of the effect sound. DIRECT LEVEL 0–100 Adjusts the volume of the direct sound. ANTI FB (Anti-feedback) This prevents the acoustic feedback that can be produced by the body resonances of an acoustic bass. Parameter/ Range Explanation FREQ1–3 (Frequency 1–3) 0–100 Set the fixed frequency point at which feedback will be cancelled. You can set up to three cancellation points. DEPTH1–3 0–100 Adjusts the degree of the anti-feedback at each of the three cancellation points. FX (Effects) Chapter 8 Parameters Guide FX (Effects) Chapter 8 Parameters Guide This is an effect that produces a long sustain by evening out the volume level of the input signal. You can also use it as a limiter to suppress only the sound peaks and prevent distortion. Parameter/ Range Explanation TYPE Selects the compressor type. BOSS COMP This models a BOSS CS-3. HI-BAND This is a compressor that adds an even stronger effect in the high end. LIGHT This is a compressor with a light effect. D-COMP This models a MXR DynaComp. ORANGE This is modeled on the sound of the Dan Armstrong ORANGE SQUEEZER. FAT When applied heavily, this compressor effect provides a fat tone with a boosted midrange. MILD When applied heavily, this compressor effect produces a sweet tone with the high end cut. STEREO COMP This selects a stereo compressor. SUSTAIN 0–100 Adjusts the range (time) over which low- level signals are boosted. Larger values will result in longer sustain. ATTACK 0–100 Adjusts the strength of the playing attack. Larger values will result in a sharper attack, creating a more clearly defined sound. TONE -50–+50 Adjusts the tone. LEVEL 0–100 Adjusts the volume. LIMITR (Limiter) The limiter attenuates loud input levels to prevent distortion. Parameter/ Range Explanation TYPE Selects the limiter type. BOSS LIMITR This selects a stereo limiter. RACK 160D This models a dbx 160X. VTG RACK U This models a UREI 1178. ATTACK 0–100 Adjusts the strength of the playing attack when the strings are played. Higher values result in s sharper attack, creating a more clearly defined sound. THRSH (Threshold) 0–100 Adjust this as appropriate for the input signal from your bass. When the input signal level exceeds this threshold level, limiting will be applied. RATIO 1: 1–.: 1 This selects the compression ratio used with signals in excess of the threshold level. REL (Release) 0–100 Adjusts the time from when the signal level drops below the threshold until when limiting is removed. LEVEL 0–100 Adjusts the volume. ENHANCER This is an effect that clarifies the contour of the input sound by emphasizing the attack of the sound following changes in the input level. Parameter/ Range Explanation SENS (Sensitivity) 0–100 This adjusts the Enhancer sensitivity. The more the value is increased, the more softly you can play and still have the effect applied. LOW FREQ (Low Frequency) 31.5Hz–125Hz Sets the low frequency range for the enhanced sound. LOW LEVEL 0–100 Adjusts the enhancer volume for the high frequency range. HIGH FREQ (High Frequency) 800Hz–8.00kHz Sets the high frequency range for the enhanced sound. HIGH LEVEL 0–100 Adjusts the enhancer volume for the high frequency range. Chapter 125 Chapter 8 Parameters Guide FX (Effects) Chapter 8 Parameters Guide FX (Effects) Adjusts the tonal quality. You can adjust the sound quality in four bands. Parameter/ Range Explanation TOTAL GAIN -20–+20dB Adjusts the overall EQ volume. Set this so that no difference in volume level occurs when switched on and off. LOW GAIN -20–+20dB Adjusts the low frequency range tone. HIGH GAIN -20–+20dB Adjusts the high frequency range tone. LOW MID FREQ (Low Middle Frequency) 20Hz–10.0kHz Specifies the center of the frequency range that will be adjusted by the LOW MID GAIN. LOW MID Q (Low Middle Q) 0.5–16 Adjusts the width of the area affected by the EQ centered at the LOW MID FREQ. Higher values will narrow the area. LOW MID GAIN (Low Middle Gain) -20–+20dB Adjusts the low-middle frequency range tone. HIGH MID FREQ (High Middle Frequency) 20Hz–10.0kHz Specifies the center of the frequency range that will be adjusted by the HIGH MID GAIN. HIGH MID Q (High Middle Q) 0.5–16 Adjusts the width of the area affected by the EQ centered at the HIGH MID FREQ. Higher values will narrow the area....