Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
. . When the Data Transfer is completed, the Display responds as shown below for a while, then returns to the display prior to the Data Transfer procedure. UTIL I TV:BULK Dur-ip Comp 1 et-e Press | EXIT j three times to return to the Play mode (the indicator goes out). 67 (S Utility Mode b. Data Transfer to a Connections How to transfer data c. Data Transfer from Connections How to transfer data MIDI Sequencer MIDI V IN MIDI OUT U-110 Set the sequencer so it is ready for receiving Exclusive messages, then take the Data Transfer procedure as shown in the previous section (on page 67). * Read the owner's manual of the sequencer you use. a MIDI sequencer MIDI I IN_ U-110 The transfer procedure is controlled from the transmitting side. You do not need to operate the receiveing unit. Before data transfer, set the transmitting and receiving unit as follows : 0Set the Control Channels of the transmitter and receiver to the same number. (Otherwise, data cannot be transferred.) #Set the Exclusive on the receiver (U-110) to ON. #|f you wish to transfer Patch data (l to 64), set the Memory Protect on the receiver to OFF. * Read the owner's manual of the sequencer you use. MIDI OUT 1 f- ::,iztmHa ЦЗПСЯСВ '■ pyp pi MIDI Sequencer 1 -r—.» MC»»OQ ! -M ЦД'ЛАД F£ OSES' Щ Ш MIDI Sequencer 68 G3 Utility Mode 2. LCD Contrast Step 1 Step 2 Step 3 Step 4 Step 5 The contrast of the Display can be adjusted. Step 1, 5 I Step Z 3 Step 4 Press EDIT to enter the Edit mode (the indicator lights up). Select “UTIL" using |'| ► |, then press | ENTER 1 . Select “LCD” using H3CE1. UTILITV:LCD CONTRAST = ÜLÜ , then press | ENTER Adjust the contrast with | DEC j and [ INC | . Press EXIT three times to return to the Play mode (the indicator goes out). *The LCD Contrast you set is retained even after the unit is switched off. 69 ® Utility Mode 3. ROM Play The U-l 10’s ROM Play function allows you to piay the demonstration songs stored in ROM. To fully enjoy the excellent quality of the sounds, use a stereo amplifier, if possible. Step 1, 5 Step 2, 3, 4 Step 1 Press EDIT to enter the Edit mode (the indicator lights up). Step 2 Step 3 Select “UTIL using | 4 \ \ ► j, then press ENTER j. Select “ROM PLY“ using !""►"], then press \ ENTER IJTL : RDM PLVüStopi 1-01 : T-Jazz......£T“ n; tr ■Sons Number >— Song Name ] : Interne! Step 4 Pressing INC | at this stage will play songs 1 to 4 in sequence. If you wish to play a specific song, select the song with [ -4 | [ ►"], then press INC |. To stop playing, press DEC Step 5 To return to the Play mode, stop playing first, then press EXIT three times. * During ROM playing, MIDI control functions are not available. * ROM performance data is not output through the MIDI OUT Song Number Song Name 1-01 T - Jazz # 1 Music by M. Sakaue (decs (c) 1988 by Roland 1-02 Swing High Music by Eric Persing (c) 1988 by Eric Persing 1-03 Cloud 9 Music by Eric Persing (c) 1988 by Eric Persing 1-04 No One Home Music by Adrian Scott (c) 1988 by Adrian Scott 70 1 Troubleshooting P, 72 2 Appendix Tables P. 76 Ш TROUBLESHOOTING Ш TROUBLESHOOTING 1. Before Calling for Repairs If the U-110 does not function properly, please refer to the following information. >No sound is heard OCheck if the Output sockets are correctly connected according to the Output Mode. [Refer to page 26. 55] OCheck if the MID! receive channel of each Part is correctly set. [Refer to page 18. 59] OCheck if the Output Assign of each Part is correctly set. [Refer to page 29„ 58] OCheck if the Key Range (Low/High) in each Part is correctly set. [Refer to page 59] OCheck if the level of each Part is not set too low. [Refer to page 31, 60] OCheck if the memory card which contains the Tone you have assigned is connected securely. ► Pitch is strange OCheck if the Master Tuning is correctly set. [Refer to page 25, 49] OCheck if the Pitch Shift in each Part is correctly set. [Refer to page 32, 61] OCheck if the Bender messages are still set ON. 72 CD TROUBLESHOOTING ► Bender effect cannot be obtained OMake certain the Pitch Bender in the Setup mode is not set to OFF. [Refer to page 50] OCheck if the -Bend Range -in each Part is correctly set. [Refer to page 61] ► MIDI Pitch Modulation is not obtained OMake certain the Control Change in the Setup mode is not set to OFF. [Refer to page 49] OMake certain the Manual Depth of the LFO is not set to zero. [Refer to page 63] 73 □ TROUBLESHOOTING 2. Error Messages When an error message is shown in the Display, resolve it as follows. * If the same error message is shown repeatedly even though everything else seems in order, call your local Roland dealer. ► Error Message shown when the battery is exhausted L- h & c k E* & "t- "t- p y ! OThe battery for the backup circuits is exhausted. Call your local Roland dealer. ►Error Message shown during Writing or Bulk Data Receiving Mode OThe Memory Protect on ...