Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
• Install the circuit board only into the specified unit (Fantom-X6/X7/X8/XR/Xa, JUNO-G, Fantom-S/S88, Fantom (FA-76), and XV-5080/ 5050). Remove only the specified screws during the installation. .......................................................................................................... • Should you remove screws, keep them in a safe place out of children’s reach, so there is no chance of them being swallowed accidentally. .......................................................................................................... This product must be disposed of separately at your local waste recycling centre. Do not dispose of in household waste bin. IMPORTANT NOTES IMPORTANT NOTES You may use any of the included phrases and/or samples in a commercial or non-commercial recording without paying any additional license fees. However, you must strictly adhere to the following crediting guidelines on any music recording that utilize material from SRX-98. Reproduction or duplication of this collection or any of the sound recording contained in the SRX-98, either as they exist on this expansion board or by any means of reformatting, mixing, filtering, re-synthesizing, processing, or otherwise editing for use in another product or for re-sale, is strictly prohibited without the express written consent of Roland. All unauthorized giving, trading, lending, renting, re-issue, re-distribution, or re-sale of the sounds included in the SRX-98 are expressly prohibited. In Plain English: Be creative in your application of the SRX-98 sounds, and keep this library for your use only. DO NOT COPY IT. Roland constantly monitors other soundware releases to check for copyright infringements, and will prosecute all piracy and copyright violations to the fullest extent of the law. THIS LIBRARY IS GUARANTEED TO BE 100% COPYRIGHT CLEAN. In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Handling the Board To avoid the risk of damage to internal components that can be caused by static electricity, please carefully observe the following whenever you handle the board. * Before you touch the board, always first grasp a metal object (such as a water pipe), so you are sure that any static electricity you might have been carrying has been discharged. * When handling the board, grasp it only by its edges. Avoid touching any of the electronic components or connectors. * Save the bag in which the board was originally shipped, and put the board back into it whenever you need to store or transport it. Veuillez suivre attentivement les instructions suivantes quand vous manipulez la carte afin d’eviter tout risque d’endommagement des pieces internes par l’electricite statique. * Toujours toucher un objet metallique relie a la terre (comme un tuyau par exemple) avant de manipuler la carte pour vous decharger de l’electricite statique que vous auriez pu accumuler. * Lorsque vous manipulez la carte, la tenir par les cotes. Evitez de toucher aux composants ou aux connecteurs. * Conservez le sachet d’origine dans lequel etait la carte lors de l’envoi et remettez la carte dedans si vous devez la ranger ou la transporter. INSTALLING THE WAVE EXPANSION BOARD * Turn off your instrument. 1. Remove the cover located on the top (or rear) of your instrument. * When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient the unit so no buttons or controls get damaged. * When turning the unit upside-down, handle with care to avoid dropping it, or allowing it to fall or tip over. 2. Insert the Wave Expansion Board connector into a connector for an SRX Series slot, while simultaneously inserting the board holders into the holes in the Wave Expansion Board. * Do not touch any of the printed circuit pathways or connection terminals. * Never use excessive force when installing a circuit board. If it doesn’t fit properly on the first attempt, remove the board and try again. 3. Use the supplied Installation Tool to turn the holders in the LOCK direction, so the board will be fastened in place. (To remove the Wave Expansion Board, turn the board holders in the UNLOCK direction, and lift up the board.) * When circuit board installation is complete, double-check your work. 4. Using the screws removed in Step 1, refasten the cover in its original position. 5. Check if the Wave Expansion Board is correctly installed. * If the “EXP” display cannot be selected (doesn’t appear) in the Waveform Selection Screen (refer to the owner’s manual of the instrument you use), remove the Wave Expansion Board and install it properly. * Eteindre l’instrument. 1. Retirer le couvercle situe sur le dessus (ou a l’arriere) de l’instrument. 2. Inserer le connecteur de la carte dans un des creneaux pour la serie SRX tout en enfoncant les supports a carte dans les trous de celle...