Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Roland
Dateigröße: 1.32 mb
Dateiname:
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
However, that ot Drum Part by NRPN is reset when receiving Program Change messages. ( Reier to //NRPN// ) (1) Modulation (#1) Status Second Third BnH 0IH vvH n = MIDI channel vv = Modulation depth : 0Н....ГН (chl...chl6) : 00Н...7Ж (O...I27) * Attects pitch modulation or rate control ( Reier to p. 19 'PATCH PARAMETERS' ) (2) Data entry (#6, #38) Status Second Third BnH 06H mmH BnH 26H IIH n = MIDI channel : OH....EH (chi...chi6) mm = MSB value ot the parameter specified by RPN or NRPN II = I SB value ot the parameter specified by RPN or NRPN (3) Volume Status Second Third BnH Û7H vvH (#7) n = MIDI channel vv = Volume : 0Н....ГН (chi...chi6) : 00H...7EH (ü...127) Real volume is determined by ( Volume value ) x ( Expression value ) x ( Master Volume value ) (4) Panpot Status Second BnH OAH (#10) Third vvH n = MIDI channel vv = Reverb send level : 0Н....Ж (ch1...ch!6) : 00Н...7Ж (0...I27) * Real sending level is determined by Volume value, Expression value. Master Volume value and this value. ( Refer to block diagram on page 20) (8) Effect3 depth (Chorus depth) (#93) Second 5DH Third vvH - MIDI channel = Chorus send level : OH....I H (chi ...chife) : 00H...7EH (0...I27) * Real sending level is determined by Volume value, Expression value, Master Volume value and this value. ( Refer to block diagram on page 20 ) (9) NRPN MSB/LSB (#98, #99) Status Second Third BnH 62H IIH BnH 63H mmH n = MIDI channel : OH....EH (chl...chl6) Il = LSB value ot the parameter specified by NRPN mm = MSB value of the parameter specified by NRPN * At power up or receiving a "Turn General MIDI System On (f 0 7E 7F 09 01 F7)" message, NRPN is not recognized ( Rx.NRPN = OIE ). System Exclusive message can enable NRPN. ( Refer to p. 19 'PATCH PARAMETERS' i //NRPN// NRPN (Non Registered Parameter Number) is the expanded Control Change message to control native functions of each MIDI instrument. NRPN is used to modify tone parameters that are relative values from preset or absolute values. NRPN MSB/LSB should be set before sending data entry. NRPN is available for only the Dn/m Part in the SCB-7. n = MIDI channel vv = Panpot : OH....EH (c h! ...chi 6) : 00H...40H...7EH (0...64. 127) I Lett..Center..Rightl 0 and 1 mean Left, 64 means Center, 127 means Right Total 127 steps from Lett to Right 15 NRPN Data Entry MSB LSB MSB LSB Description I8H rrH mmH — Pitch coarse ot Drum Instruments (relative change) mm : ООН...71 El (-64...0...+63 semitones) IЛМ rrH mmH — IVA level ot Drum Instruments (absolute change) mm : 00Н...7ГН ICH rrH mmH — Panpot o! Drum Instrument (absolute change) mm : 01 H...40H...7IH (Lett-Center-Right) I DH rrH mmH..... Reverb send depth ot Drum Instruments (absolute change) mm : ООН...71 H I EH rrH mmH — Chorus send depth ot Drum Instruments (absolute change) mm : 00H..7FH rr: key number oi Drum and Percussion * LSB ot data entry is ignored. * Relative parameter specifies relative value regarding preset value as 40H. * Absolute parameter specifies absolute value regardless ot current value. « How to use NRPN » Recognizing NRPN is always oft at power up or when receiving 'Iurn CM System On’, because parameters specified by NRPN can be assigned native functions of each MIDI instrument and may cause problems. NRPN is available for only the Drum Part in the SCB-7. (1) Enable to receive NRPN by System Exclusive message ' E0 41 1056 1201 0001 01 sum(7D)F7' Part 10 = Drum Part RPN Data Entry MSB LSB MSB LSB Description 00H OOH mmH — Pitch bend sensitivity mm : 00H...I8H (0...24 semitones) * Up to 2 octaves; default setting is 2 semitones OOHOIEi mmH IIH Master tine tuning mm,II : OOH,0OH...40H,OOH...7FH,7FH (-100......0......+ 100 cent) OOH 02H mmH --- Master coarse tuning mm : 28H...40H...58H (-24....0....+24 semitones) 7FH 7FH RPN reset * No specified parameter is assigned to RPN and NRPN. Current value is not affected. « How to use RPN » ( I ) Specify the parameter to RPN Bn 65 пил (Bn) 64 II mm: MSB ot parameter name li: I SB ot parameter name (2) Set parameter value using data entry (Bn) 06 vm (Bn) 26 vl vm : MSB ol parameter value vl: LSB ot parameler value Sending only the MSB value is possible, if the required resolution ol the value is I 20 steps. Omitting the MSB value is allowed, if the required range of the value is less than 128. (.}) Reset RPN ( no parameter specified by RPN ) (Bn) 6r> 7F (Bn) 64 7F (2) Specify the parameter to NRPN B9 6) mm (B9) 62 II mm: parameter II: key number of Drum Instrument ( ?) Set parameler value using data entry (B9) 06 vv vv: parameler value ( use only MSB in SCB-7 ) (4) Reset NRPN ( no parameter specified by NRPN ) (B9) 65 7F IB9) 64 7F Once the parameler is specified by NRPN (Step 2), all values sent by data entry are valid (Step 3). It is recommended to reset NRPN after sending the value so as to avoid any problems (Slep 4). (10) RPN MSB/LSB (#100, #101) Status Second Third BnH 64H IIH BnH ...