Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
12 • Any of the effect programs written in memory- can 23 Memory............................................................. 13 be called with program change messages sent .1. Writing into Memory........................................ 13 from an external MIDI device. 2. Selecting an Effect........................................... 14 a. Changing Memory Numbers ....................... 14 b. Changing Memory Numbers via MIDI ......... 14 3. Restoring the Pre-programmed Effect Programs .......................................................... 17 ■ Block Diagram ................................................... 18 ■ Specifications .................................................... 21 3 ■ PANEL DESCRIPTION FRONT PANEL REAR PANEL 0 MIC Sockets 1 and 2 (P6) Connect a units such as a microphone to this socket. 0 Input Level Control Knobs 1 and 2 (P8) The input level of the unit connected to the MIC Socket is adjusted with these knobs. O Warmth Control Knob (P10) This controls the "warmth" of the effect sound. o Echo Level Control Knob (P10) This adjusts the volume of the echo sound. 0 Repeat Rate Control Knob (P11) This changes the speed of echo repeats. © Intensity Control Knob (P11) This changes the number of echo repeats. 0 Reverb Control Knob (P11) This controls the depth of reverberation effects. 0 Level Indicators (P8) These indicate the level of the input signal. 0 Display This shows the current Mode and conditions. 0 Mode Button (P8) Pushing this button selects the five preset echo patches (=Modes) in sequence. 0 MIDI Button (P15,16) Press this button for controlling this unit via MIDI. 0 Memory Button (PI4) Use this button to call any of the effect programs written in the RE-3's memory. 0 Write Button (P13) Press this button for writing the edited effect program. 0 Power Switch (P6) © LINE IN Socket (P6) This is to connect a line-level device such as a mixer. © Level Selector Switch (P7) This selects the input/output level. Change the positions depending on the type of the unit you use. 0 Direct Switch (PS) The MIX position provides a mixed sound of the direct and echo signals, and "Cancel" gives only the echo sound. When using the Effect Send/Return socket on a mixer, set this switch to "CANCEL". (When using microphone input, the "MIX" mode is matter which position the switch is set to.) © Output Socket A/mono (P6) 0 Output Socket B (P6) These are output sockets. Use both of then for stereo output, and use the A socket for monaural output. ® Effect ON/OFF Socket (P12) The effect can be turned on or off using the footswitch or pedal switch connected to this socket. MIDI IN Socket (P14) ® Power Cord ■ IMPORTANT NOTES Location • Operating the unit near a neon or fluorescent lamp may cause noise interference. If so, change the angle or the position of the unit. • Avoid using the unit in excessive heat or humidity or where it may be affected by direct sunlight or dust. Power • The appropriate power supply for this unit is shown on its name plate. Please make sure that the line voltage in your country meets the requirement. • It is normal for this unit to become hot while being operated. • Do not drop or place anything heavy on the power cord or connection cords. Caution • Do not dismantle or touch inside the unit. It may cause you an electric shock and the unit breakdown. • Do not let any solid or liquid substance into the unit. • If the unit does not function properly,, immediately switch it off, disconnect the power plug from the socket, and call your local Roland service center. Other Notes ® For about five seconds after the unit is switched on, muting circuits function, therefore no sound (effect or direct) is produced. • If this unit is turned on immediately after being turned off, it may not function properly. If this happens, turn off the unit once, then turn it on after waiting for a few seconds. • The RE-3 features a memory back-up system that retains the data even when switched off. The battery that supports the back-up circuit should be replaced every five years. Call Roland for battery replacement. (The first replacement may be required before five years, depending on how much time had passed before you purchased the unit.) ■ CONNECTIONS MIC1 MIC MIC2 Rolarte I SB kCE ECHO оом.. .с. Ó о о о о ; : С ЧГ_31' MIDI Device Foot Switch INPUT(R) 1 '1 INPUT(L) Amplifier Speaker When using the LINE IN socket Roland SPACE ECHO » О О О О О О О * When using the RE-3 with mixer set the Diect switch to "Cancel" 6 ■ PROCEDURE Ш OPERATION 1. Basic Procedure a. Basic Level Setting When all the necessary connections are made, follow the procedure: © Make sure that the unit is turned off, then connect the power plug to the socket. (2) Turn the unit on. Set the Level Selector Switch to an appropriate position as follows; • When using the MIC 1 and 2 sockets Set the Level Selector switch depending on the input level ...