Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Roland
Dateigröße: 1.59 mb
Dateiname:
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
See page 18. Note: You can store this setting so that it will be used next time you switch on the RD-150. There is only one memory, however, so that the previous sellings will be overwritten whenever you store your new panel settings. Hold down IFUNCTIONI while pressiwlCHOIRl. Then confirm by pressing DATA [+]. 4.7 Splitting the keyboard The RD-150 allows you to divide the keyboard into two sections,“Upper” and “Lower”, and to play two different Tones with your left and right hands. Dividing the keyboard is called “Split”, and the key where the keyboard is split is the “split point”. I J n I L LI 1. Start by selecting the Tone that you want to use in the right half (see “Selecting sounds” on page 11). 2. Press IS P LiTl (indicator lights). The Tone you selected before pressing ISP LiTl can be played via the right half of the keyboard. This is the Upper Tone. The RD-150 automatically assigns a matching Tone to the left half (the lower Tone) and also transposes either the Upper or Lower Tone, or both. See “Split mode (default split point: Gb3)” on page 24 for details. You can, however, select a different Lower Tone. 3. Adjust the volume balance of the two Tones with the Level IIP WERI and lUPPERj sliders. 4. PressISPLITl once again (indicator goes dark) to leave the Split mode. Note: You can also select which Tone(s) should respond to footswitch and/or pedal messages. See page IS. Using different Tones in Split mode It is also possible to select different Tones for the Upper and Lower sections after activating the Split mode (whilefSPTTTl lights): Press a Tone selection button to assign a different Tone to the Upper section. In this case, the Lower Tone does not change. To select a different Tone for the Lower section, press and hold the Tone selection button of the Tone you wish to assign to the right half (Upper), while pressing the Tone selection of the desired Lower Tone. Press and hold... Piano Piano ... while pressing. Strings Pad n9- V (new Lower Tone) 12 RD-150 - Using effects Noli’: You can store this setting so that it will be used next time you switch on the RD-150. There is only one memory, however, so that the previous settings will be overwritten when you store your new panel settings. Hold down IF UNCTION] while pressing [CHOTfD. Then confirm by pressing DATA 0. Changing the split point When you activate the Split mode, the keyboard will be split at the “Gb3”, i.e. the Gb key more or less in the middle. You can, however, select a different split point: 4.8 Using effects Hold down n The split point can be set anywhere between the C2 and the C6. There are two ways of changing the split point: 1. Press and hold ISPLITl while setting the desired split point with the DATA[±]/E] buttons. The display briefly confirms the note you selected. 2. Press and holdlSPUTl while pressing the desired key on the keyboard. Note: You can store this setting so that it will be used next time you switch on the RD-150. The RD-150 comes with three digital effects: Chorus, Reverb, and Sympathetic Resonance. While Chorus and Reverb are available for all Tones, Sympathetic Resonance can only be used with piano Tones. Adding Chorus Chorus is an effect that gives the impression that several instruments arc being played at the same time. As a result, the sound will be fatter and have more presence. The depth (volume) of the Chorus effect can be set in eight steps. Press ICHOKUSI and confirm that its indicator lights. Note: The Chorus effect can be switched on and off for each Tone separately. Changing the depth of the Chorus Set the depth by holding down ICHORUSl while pressing DATA 0 /0. Note: The depth is preset for each Tone, but can be changed. Adding Reverb By using the Reverb effect, you can obtain pleasant reverberations like those in a concert hall. The depth of the Reverb effect can be set in eight steps. Press IR EVE RBI and confirm that its indicator lights. Changing the depth of the Reverb Set the depth by holding down iREVERBl while pressing DATA 0/0. Note: The depth is preset for each Tone, but can be changed. 13 RD-150 Owner's Manual—Preparations and main functions Sympathetic Resonance On an acoustic piano, depressing the damper pedal makes the notes you play resonate with other strings, adding rich reverberations and thickness to the sound, The RD-150 simulates this effect for the piano Tones flPlANOl -IROCK PlANOl and Variation Tones). The effect, called Sympathetic Resonance, is automatically added to these Tones, but you can vary the depth in eight steps. Note that it is only audible when you use the foot-switch connected to the iDamperl jack. Pedal Damper Soft/Expr. # ® 1. Simultaneously hold down IchorusI and IREVERBI. The display now indicates the current Sympathetic Resonance depth. 2. Keep holding iCHORUS] and IR EVE R BI while setting the desired depth with DATA 043 • Note: The setting is at "4" when the RD-150 is powered up. You can, howev...