Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
If casters have been attached to the amp, make sure it is used only on a stable, level surface. 7 Attaching the Mount Bars and Clamps 1. As shown in the figure, turn the satellite speakers over and place them on the floor, then screw in the mount bars. * To protect the satellite speakers cosmetic appearance, place cloth or paper between the speakers and the floor surface when attaching mount bars. * You can screw in the mount bars with less force by inserting a screwdriver or other rigid shaft into the holes in the side of the mount bars and grasping and rotating the shaft to screw in the bars. 2. Loosen the provided clamp screws to open the clamps. 3. Attach the clamps to the pipe used for securing the satellite speakers (diameter 1-1/2 inches / 38.1 mm), and screw them tight enough to prevent them from slipping down (provisionally tighten). 4. Take the satellite speakers with the mount bars attached to them and insert the ends of the mount bars into the clamps provisionally tightened in Step 3. 5. Slowly tighten the screws to firmly secure the clamps. * To keep the units from separating and falling, secure the mount bars in a position such that the ends of the mount bars extend at least 20 mm (13/16 inch). To prevent the satellite speakers from falling, release them only after confirming that they are firmly secured. To prevent the satellite speakers from overturning, attach them so they are oriented perpendicular to the floor. Take care not to allow hands and fingers to become pinched when attaching and removing the units. 20 mm (13/16”) or less s Main Unit: Front Panel 1 3 5 7 8 9 10 11 12642 V-DRUMS/CH1 1. PUNCH Switch Setting this switch to ON produces a dynamic drum sound while increasing the perceived power of the sound. Switch this on whenever needed. * The effect of this function is applied to the device connected to V-DRUMS/CH1. 2. VOLUME Knob Adjusts the volume of the device connected to V-DRUMS/CH1. * If you connect a sound module with a high output level , distortion may occur if you turn the volume level up too much. Be careful. CH2 3. VOLUME Knob Adjusts the volume of the device connected to CH2. CH3 4. VOLUME Knob Adjusts the volume of the device connected to CH3. WOOFER CONTROL 5. MODE SELECT Switch This switches the range of sound output from the main unit. SUBWOOFER: Only sounds in the low-frequency range are output. When used together with the satellite speakers, this mode produces a drum sound with great presence. This is optimal when V- Drums stands are used. FULL RANGE: This provides powerful, full-range sound, from low frequencies on up to the high end.This also enables the unit to be used for smaller ensemble performances as a main speaker for the V-Drums. * This does not affect the sounds output from the SPEAKER OUT, headphones, and LINE OUT outputs. “Setup Examples” (p. 12) 6. VOLUME Knob Adjusts the volume of the main unit. You can use this to achieve a volume balance between the main speaker and the satellite speakers. * This does not affect the sounds output from the SPEAKER OUT, headphones, and LINE OUT outputs. * No sound is output from the PM-30's speakers when the WOOFER CONTROL VOLUME knob is set to 0. MASTER EQUALIZER 7. EQUALIZER (BASS) Knob Adjusts the low-frequency tone quality. 8. EQUALIZER (MIDDLE) Knob Adjusts the midrange tone quality. 9. EQUALIZER (TREBLE) Knob Adjusts the high-frequency tone quality. 10.VOLUME Knob Adjusts the volume of the overall system. * When headphones are connected, this adjusts the headphone volume. * This does not affect the output to LINE OUT. 11. PHONES Jack Connect the system headphones (optional) here. * No sounds are output from the main unit speaker or satellite speakers when headphones are connected. 12. POWER Switch This turns the power to the system on and off. * If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 5). * To prevent damage to the system and any connected devices, turn the power on and off according to the instructions in “Switching the Power On and Off” (p. 10). * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. Panel Descriptions Panel Descriptions l 13151718 16 14 V-DRUMS/CH1 13. V-DRUMS Input Jack Use a single stereo cable (sold separately) to connect the output from the V-Drums sound module’s PHONES OUT to this input jack. For more detailed information with examples of using VDRUMS input, refer to “Connections” (p. 10). 14. LINE IN (L/MONO, R) Jack Connect V-Drums sound modules and other line-level devices here. Connect devices with monaural output to the L/MONO jack. CH2 15. LINE IN (L/MONO, R) Jack Connect line-level devices (e.g., synthesizers and sound modules) here. Connect devices with monaural output to the L/MONO jack. CH3 16. LINE IN (L/MONO, R) Jack Connect line-level devices (e.g., recorders, CD/MP3...