Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
(This is important because it affects response and triggering characteristics.) Never fully tighten a single tuning bolt all at once. Doing so makes it impossible to tension the head evenly. It should feel about the same as an acoustic drum, or a even slightly tighter. Tension that is too loose may cause triggering problems. The tension may change when the pad has been in use for some time. Re-tune as required. Adjusting the head tension affects response and triggering, and does not change the pitch of the sound, as it would on an acoustic drum. Installing the RT-5S and the Optional RM-2 1. Mount the RT-5S (Snare Trigger) so it does not interfere with your playing. For information on adjusting the height of the RT-5S's sensor, refer to the owner's manual for the RT-5S. 2. Turn the RIM level knob for the RT-5S clockwise to set the output level for rim signals at maximum. 3. Next, attach the bracket and the RM-2. Tighten the bolts at the two locations shown in the figure. 4. Tighten the mounting screw for the bracket you installed in step 3 to attach the hoop to the snare drum. Install at a location where it does not interfere with the tuning bolt to the immediate right of the RT-5S (see illustration). 1 PCK-1 Practice Conversion Kit Owner's Manual Installing the Rubber Rim Silencer Attach the either the rubber rim silencer for a steel (press) hoop or the rubber rim silencer for a die-cast hoop, depending on the type of hoop on your snare drum. Attach it on the side closest to you, where you will make rim shots. Cross-section shape: For a steel (press) hoop For a die-cast hoop Depending on the shape of the hoop, the rubber rim silencer may come loose. If this happens, use double-sided tape between the hoop and the rubber rim silencer as required to secure the rubber rim silencer in place. Connecting and Making the Settings for the Optional RM-2 1. Using the included stereo cable, connect the OUTPUT jack on the RT-5S to the TRIG1 jack (TRIGGER INPUT 1) on the RM-2. 3. When connecting the RT-5S, be sure to connect the cable to TRIGGER INPUT 1, and connect nothing to TRIGGER INPUT 2. The RM-2 will not operate correctly if a cable is connected to TRIGGER INPUT 2. Hold down the [SEL] button and switch on the power. This is how you can set the trigger parameters. Press the [▲ ]/[ Y ] buttons to change the input mode to H-r (Head & Rim). 4. Press the [SEL] button. After tyP is displayed, you can select the trigger type. Press the [a ]/[y] buttons to choose PIE (PD-120). 5. 6. Make settings as shown below, pressing the [SEL] button to change parameters and the [ A ]/[ Y ] buttons to change values. Parameter Value thr (Threshold) 8 SnS (Sensitivity) 11 Cur (Velocity curve) Lnr (LNR) Sen (Scan time) 32 (3.2 msec) rtC (Retrigger cancel) 5 Cr5 (Crosstalk cancel) oFF (OFF) il5U (Mask time) 8 (8 msec) r i 11 (Rim sensitivity) 15 rflG (Rim gain) *1 20 *1: After setting the rim sensitivity, holding down the [TAP] button and pressing the [SEL] button enables you to set the rim gain. 7. Press the [METRONOME] button to return to the normal tempo-display screen. Changing the sound of the RM-2 1. Press the [SEL] button several times to make the "PAD INST" indicator flash. 2. To select the head sound, strike the head. The "TRIG1" indicator flashes. 3. Press the [ A ] / [ Y ] buttons to choose a tone. 4. To select the rim sound, hit the rim. The "TRIG2" indicator flashes. 5. Press the [ A ]/[ Y ] buttons to choose a tone. To Achieve Greater Muffling We advise to use this system with the snares turned OFF. If you want even more of a muffled effect, insert a sponge or cloth between the snare strainer and the bottom head. This suppresses vibration and resonance of the bottom head. Specifications PCK-1: Practice Conversion Kit Contents: RT-5S Snare Drum Trigger 14-inch Mesh Head Two types of Rubber Rim Silencers RM-2 Mounting Bracket Connection Cable (0.2 m / 7-7/8 inches) Accessory: Owner's Manual * Installation on all types of snare drums may not be possible. Installation on some snare drums may NOT be possible if the height from the upper edge of the rim to the head is more or less than 7/16-5/8 inch (11-15 mm). * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. Copyright © 2003 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. 2 РСК-1 7.ZT • • Фу Ь тшют ШМШШЛ'У Ь‘«л,§ ЬЬ-_>^Ш0ф'У hrto ÎMM/PmiiUin/c 14 -¿vîsil • л'У b‘£tt ЩЬТС^^о RT-5SX*7- bUtf-të^'y bchUA^S^CbU^U 'JA • '>з'У ЬВ#0Ж*Й£ЙЛ^?-Х • ^Л-^ttJS ЬТС^^о S!JroU(DUXA • □-^ (RM-2) &ШУШТЁ-^ШУ ^^'У Ь^ЩЬТС^-Го Ш Ч # Cf 3 /Ш1Т 3 /KÆ Т 3 ^ V у л. • 'Vy K£BWttlt3 Х^КТ7 • b^ACD'Vy K^^bbs 14 • y^vVzL • л'у 1. • Ж^Ь^'У^-^ЖУ^ЬЬ • ЖЛу Ь^'У^-^сКё#^^ ¿ТЙШ<£:£1Л о 2. y-yt'W K^y^fbiîo 3. ^xJb0±MJ10y<'y^^ • Л'у b^öMtä^o 4. ¿"¿'Ун ■ sw ...