Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
* You can set the Amp Control independently of the effect On/Off settings. * You can store separate Amp Control settings to each memory. For more on this procedure, refer to “Storing Settings (Write Operation)” (p. 10). With Amp Control, not only can you switch amp channels, you can also use it to switch the amp’s effects on and off, like a foot switch controller. Operation Storing Settings (Write Operation) Storing the “MANUAL” Sound in Memory Do not switch off the power while a write operation is in progress. 1. Create the sound you want when set to “MANUAL.” 2. Press the MEMORY WRITE button. The MEMORY indicator and the indicator for the currently selected memory blink, and the OD-20 is put into write standby. Write standby Blink Blink 3. Press the MEMORY SELECT button to select the memory (number) to which you want to store the sound. The indicator for the selected MEMORY number blinks. Blink Blink Operation 4. Press the MEMORY WRITE button. The write operation finishes after the MEMORY indicator and the indicator for the write-destination memory have begun to blink more rapidly. Writing Write finished Blink rapidly Lit Blink * To cancel the write operation, operate a knob or the MANUAL/MEMORY pedal before you press the WRITE button. Operation Changing and Storing the “MEMORY” Sound Do not switch off the power while a write operation is in progress. 1. Press the MANUAL/MEMORY pedal or the MEMORY SELECT button to change to the “MEMORY” sound. 2. Operate the knobs to change the sound. * To avoid sudden inadvertent changes in sound, the DRIVE, BOTTOM, TONE, LEVEL, ATTACK SHAPE, and HEAVY OCTAVE knobs are designed so that the setting does not change unless the knob is first turned as far as the stored setting value. Once the position of the knob matches the setting value stored in memory, the sound starts to change. When a setting changes, the MEMORY indicator blinks automatically. Blink 3. Press the MEMORY WRITE button. The MEMORY indicator and the indicator for the currently selected MEMORY number start to blink, and the OD-20 is put into write standby. Write standby Lit Blink Blink Operation 4. Press the MEMORY SELECT button to select the memory (number) to which you want to store the sound. The indicator for the selected MEMORY number blinks. Blink Blink 5. Press the MEMORY WRITE button. The write operation finishes after the MEMORY indicator and the indicator for the write-destination memory have begun to blink more rapidly. Writing Write finished Blink rapidly Lit Blink * To cancel the write operation, operate a knob or the MANUAL/MEMORY pedal before you press the WRITE button. And the OD-20 is returned to the status in effect in Step 2. 14 Part Names and Functions Front Panel fig.19 DRIVE Knob Adjusts the amount of distortion. Turning the knob to the right (clockwise) creates a stronger distortion and increases the volume. Turning this all the way to the TURBO range increases the effect even more. BOTTOM Knob Adjusts the low frequency range. Turning the knob to the left (counterclockwise) cuts the low end more; the low frequencies are boosted as the knob is turned to the right. Optimized for the distortion selected with “TYPE.” TONE Knob Adjusts the tone. Turning the knob to the left creates a milder sound; a sharper sound is produced as the knob is turned to the right. Optimized for the distortion selected with “TYPE.” ATTACK SHAPE Knob Changes the tone of the attack portion. Turning the knob to the left of the center position results in a smoother tone; a tone with a more prominent edge is created when the knob is turned to the right of center. LEVEL Knob Adjusts the volume. HEAVY OCTAVE Knob Adds sound an octave below what is performed by the guitar when playing in the low registers. Turning the knob to the right raises the level of the octave sound. Output of the octave sound ceases when the knob is turned completely to the left. * No octave sound is added when you play in the high-middle registers. 15 Part Names and Functions fig.20 MEMORY SELECT Button Use this to select a Memory (1–4), and to specify the write destination when carrying out the write procedure. * When “1” is selected as the Pedal mode (p. 6), you can switch between “Manual” and “Memory (1–4).” MEMORY WRITE Button Press this to store settings in “MEMORY.” MEMORY Number Indicator (1–4) The indicator for the currently selected MEMORY number (1–4) lights. The indicator flashes while the OD-20 is in write standby; the indicator flashes more rapidly while the write operation is in progress. TYPE Knob VARIATION Button Select the distortion type with the TYPE knob, then press the VARIATION button to select the variation. The button's indicator lights up when a variation is selected. “TYPE List” (p. 16) AMP CTRL (amp control) Button This switches the amp channel when you have the guitar amp’s channel switching jack connected to the OD-20’s AMP CTRL jack. Part Names and Functions TYPE List * All product names mentioned in this document a...