Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
It produces soft and natural sound distortion just like an overdriven valve-amplifier but it preserves the tone quality of the guitar you play. NAME AND FUNCTIONS AC ADAPTOR JACK LEVEL*- ■♦CHECK LAMP -•OVER DRIVE LEVEL OVERDRIVE OUTPUT JACK•—(if4“Olirr!^T■ INPUT4* |h-• INPUT JACK PEDAL SCREW OVER DRIVE This knob controls level of over-drive tone (soft distortion). Turn clockwise (O) to lift and counterclockwise (O), to cut. LEVEL This knob functions to compensate for the level difference between Normal and Effect settings. Turning clockwise (O) increases volume of Effect mode and counterclockwise (H), decreases. INPUT JACK This input jack receives output from electric guitar and other electronic instruments. OUTPUT JACK This jack feeds signal to amplifier. AC ADAPTOR JACK OD-1 operates both from self-contained battery (9V) and from AC line. Connect a BOSS AC Adaptor (DC9V) to this jack, and the battery is disconnected from the circuit, guaranteeing stable long-time performance. PEDAL SWITCH This is a changeover switch for Normal or Effect. By use of FET ELECTRONIC SWITCH, first in these kinds of small size effect units, pop noise is perfectly eliminated and OD-1 can be satisfactorily employed even in studio recording. CHECK LAMP While pedal is trod down, this lamp lights if battery is normal. Thus this lamp lets you confirm the changeover between Effect and Normal modes, and also battery state. If the indicator fails to light, replace the battery with a new one. SCREW When replacing battery, loosen this screw to open the casing. Do not remove off the screw from the pedal. If you do, be careful not to lose it. BEFORE USING OD-1 • When operating OD-1 from AC line, use BOSS AC Adaptor for OD-1. • Avoid using OD-1 in very dusty location or under high temperature or humidity conditions. CONNECTING OD-1 ■to u AC ADAPTOR JACK LI BOSS AC ADAPTOR © GUITAR AMPLIFIER BOSS OD-1 OPERATING OD-1 1 2 After connecting ail cords required, set all knobs on the panel as illustrated. Tread the pedal to check battery. If check lamp lights, battery is live. * If lamp does not light, which means dead battery, replace with a new battery. CHECK O Tread pedal to set the unit in the state that sound is effected. Turn Over Drive knob to proper position. While switching pedal ON and OFF, turn Level knob to proper position so no volume difference between Normal and Effect modes is noticed. CAUTIONS FOR REPLACING AND HANDLING BATTERY BATTERY STRAP BATTERY CONNECTOR 9V BATTERY PEDAL (COVER) /-SCREW SPRING BASE COIL SPRING PEDAL GUIDE BATTERY HOUSING REPLACING BATTERY USE ONE 9-VOLT BATTERY. O Loosen the screw of pedal to open it and take out battery from its housing. 0 Replace the battery by a fresh one and put it into position. 0 Set coil spring onto the projection on the rear of the pedat and shut the cover (pedal). Finally, insert the screw into the pedal guide and tighten it. At this time, be careful not to catch the battery strap in the cover or coil spring. CAUTIONS • When you don't use for a long period, remove the battery to prevent current leakage and leaking out of sticky substance. • If battery voltage drops, effect becomes inferior or no sound is produced. To prevent that, replace the battery a little earlier. Be sure to keep the battery snapped by connector into the housing, when using AC adaptor, too. * Even if AC Adaptor cord comes out during performance, operations immediately changes to battery, causing no trouble in continued performance. Power is switched on while a plug is put into input jack. When you do not use, keep the plug off the jack. AC ADAPTOR (OPTION) When you operate OD-1 from AC line, use AC Adaptor (DC9V) for OD-1. BOSS ACA-120 FOR 117V AC BOSS ACA-240 FOR 240V AC BOSS ACA-220 FOR 220V AC (^Roland® 10417 UPC 10417 SPECIFICATIONS Power...............Battery 9V (1) AC Adaptor Current draw . :......... DC9V, 3.5mA Control ..............Overdrive, Level Others...............Normal/Effect Changeover Switch, Battery Check Lamp (also for confirmation of Normal/Effect changeover) Jack.....................Input, Output, AC Adaptor S/N ratio .............Over 80dB Input impedance......... 220K12 Output load impedance Over 60057 Dimensions............70(W) x 55(H) x 125(D)mm Weight,.............. 400g * Specifications are subject tcf change without notice. OI3DSS Products of Roland Prin...