Anleitung Roland, modell MS-50
Hersteller: Roland Dateigröße: 210.62 kb Dateiname:
Unterrichtssprache:
|
|
|
|
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite
Anleitung Zusammenfassung
To ensure proper use of this speaker, please read these instructions carefully. FEATURES 0 High quality output suitable for monitor applications. 0 Two-way, bass reflex design; rated input of 50 watts. • A magnetically shielded mid/low driver and a horn tweeter. • Push terminals and phone jack for signal input. 0 Compact design. 0 Optionally available Speaker Holder for wall or ceiling installation. Connection Sample Setup Power Amp MS-50 * Before making any connections, be sure the power to all equipment is OFF. * Excessive input power levels can severely damage this speaker. Copyright © 1992 by ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Connecting Skeaker Cord Determine which of the two input connector types you wish to use. * Push Terminals Press the terminal tab and Insert the bare wire of the speaker cord into the hole. When you release the tab, the speaker cord will be held firmly in place. Carefully observe the polarity of the terminals: red is positive (+) and black is negative (-). * Phone Jack The polarity of the plugs is as shown below. Plug Polarity Positive (+) * Never use both the push terminals and phone jack at the same time. (The reason for this is that the push terminals and phone jack are internally connected in parallel.) Attaching the Speaker Holder With the optionally available Speaker Holder (SPH-50), the speaker can be securely mounted on ceilings or walls. * With the Speaker Holder attached, the speaker appears as shown below. (To attach the holder to the speaker, use the supplied M6 X 15 screws and M6 X 1.5t washers.) Protecting the Speakers from Damage Excessive power input can severely damage this speaker system. While the speaker can absorb larger input peaks, be sure the continuous power input does not exceed 50 watts. Placement • The combined weight of the speaker and the holder (SPH-50) is approximately 4 kilograms (9 lbs). Be certain that the particular section of ceiling or wall onto which you intend to attach the speaker will be able to adequately support this weight. • Be aware that high volume levels may produce undesirable resonances (vibrations) in the wall or ceiling to which the unit is attached. Be sure the mounting surface is reasonably solid. • Even though this speaker is magnetically shielded, it may still generate a magnetic field. Never place floppy disks (or any other magnetic storage media) anywhere near the speaker: the magnetic field may erase the data stored on the disks. • The magnetic field generated by this speaker may also cause interference in televisions or video display terminals. In such a case, simple move the speaker away from the monitor. Important Notes • When making any connections with other devices, always turn off the power to all equipment first; this will help prevent damage or malfunction. • Do not subject the unit to temperature extremes (eg. direct sunlight in an enclosed vehicle). Avoid using or storing the unit in dusty or humid areas or areas that are subject to high vibration levels. • Do not expose this unit to temperature extremes (eg. direct sunlight in an enclosed vehicle can deform or discolor the unit) or install it near devices that radiate heat. • For everyday cleaning wipe the unit with a soft, dry cloth (or one that has been slightly dampened with water). To remove stubborn dirt, use a mild neutral detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. • Never use benzene, thinners, alcohol or solvents of any kind, to avoid the risk of discoloration and/or deformation. Specifications •Speakers 12cm/4-3/4inches Woofer(Magnetically shielded) Drirer with a Horn (Magnetically shielded) •Rated Input 50W •Maximum Input 100W •Rated Impedance 40 •Sensitivity 92dB(1W,0.5m) •Crossover Frequency 3kHz •Connectors Input Jack(1/4 inch phone type) Input Terminal •Enclosure Bass-refrex type •Material and Finish Body:ABS (black, painted) Speaker Grille:Punching Metal Grill •Dimensions 166(W) X179(D) X242(H)mm 6 —9/16(W) X7-1/16(D) X9 —9/16(H) inches •Weight 3.2kg 7 lbs 1 oz •Accessories Owner’s Manual •Options Speaker Holder SPH-50 * In the interest of product improvement, the specifications of this unit are subject to change without prior notice. Information When you need repair service, call your local Roland Service Station or the authorized Roland distributor in your country as shown below. U. S. A. SPAIN NEW ZEALAND EGYPT THAILAND Roland Corporation US Roland Electronics Roland Corporation Al Fanny Trading Office Theent Music Co , Ltd 7200 Dominion Circle de España, S. A, (NZ) Ltd. 9, Ebn Hagar Askalany 330 Verng Nakorn Kasem, Los Angeles, CA Calle Bolivia 239 97 Mt. Eden Road, Mt, Street, Ard El Golf, Soi 2. Bangkok 10100, 90040-3647, U. S. A. 0S020 Barcelona, SPAIN Eden, Auckland 3, Heliopolis, Cairo, EGYPT THAILAND 0...