Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
* If there is a batteries in the unit while an AC adaptor is being used, normal operation will continue should the line voltage be interrupted due to power blackout or power cord disconnection. * Some connection cables contain resistors. When connection cables with resistors are used, the sound level to be extremely low, or impossible to hear. For A NOTE About Placement information on manufacturer of the * Once the connections power to your various devices By turning on devices in the causing malfunction and/or other devices. When powering up: Turn on the power to your guitar amp When powering down: Turn off the power to your guitar amp first. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * When operating on battery power only, the CHECK indicator will become dim when battery power gets too low. Replace the battery as soon as possible. BOSS Compact Pedals have a non-slip rubber pad attached to its and temperature of the surface on which you place the Compact or mar the surface. You can place a piece of felt or cloth under the unit If you do so, make sure the unit will not slip or move accidently during use. Connections AC Adaptor BOSS PSA-series (sold separately) OUT 9V DC/200 mA Guitar Amp Electric Guitar Connections AC Adaptor BOSS PSA-series (sold separately) OUT 9V DC/200 mA Guitar Amp Electric Guitar * This unit is equipped with a protection circuit. A brief interval (a few required before the unit will operate normally. Operating Operating 1. After you have made the 2. Depress the pedal switch 4. Adjust the amount of necessary ( p. 7, 8) connec- to turn the effect on. (The high-frequency sound tions, set the panel knobs CHECK indicator lights with the HIGH knob. as shown in the illustra- when the effect is on.) tion. 3. Adjust the amount of distortion with the DIST knob. Operating Operating 5. Adjust the amount of low-frequency sound with the LOW knob. 6. Adjust the output volume with the LEVEL knob. Normally, you should adjust the LEVEL knob so there's no difference in the volume when switching the effect on and off. Changing Changing * The use of an AC adaptor is recommended unit’s power consumption is relatively you prefer to use a battery, please use Thumbscrew Pedal Spring Base Battery Snap Cord Coil Spring Guide Bush Hole Battery Snap Battery Housing 9V Battery 1. Loosen the thumbscrew the pedal, and upwards to open * The thumbscrew can be left changing the battery. 2. Remove the old battery from housing, and remove the snap to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery’s polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely. Troubleshooting Troubleshooting . Is the specified adaptor separately) properly Check the AC adaptor connection p. 7, 8). * Never use any AC adapter other specified for use with the ML-2. . Is the battery low or dead? Replace it with a new battery ( p. 11). * The battery that is supplied with the unit is temporary use, intended primarily for testing the pedal’s operation. * The use of an AC adaptor is recommended as the unit’s power consumption is relatively high. Should you prefer to use a battery, please use the alkaline type. * To prevent unnecessary battery consumption, be sure to disconnect the plug from the INPUT jack when not using the effects unit ( p. 5). . Is your guitar properly connected to the INPUT jack? Check the connection once more ( p. 7, 8). * A cable must be allow the effect to * If a cable is connected to the unit (either from adaptor), the CHECK indicator when you try to turn the effect No sound / low volume . Is your instrument properly connected the ML-2? Check the connection once more ( p. 7, 8). . Is the LEVEL knob set too low? The further counterclockwise you turn the LEVEL knob, the more the volume is reduced when the effect is on. Turn the LEVEL knob clockwise to increase the volume. . Is the volume turned down on any guitar amp or effects device you have connected? Check the settings of the connected device. . Is the battery low or dead? Replace it with a new battery ( p. 11). Setting Setting Blast beat metal Gothenburg sound Setting Setting Specifications Specifications Nominal Input Level........................ -20 dBu Input Impedance............................... 1 M. Nominal Output Level..................... -20 dBu Output Impedance ........................... 1 k. Recommended Load Impedance.... 10 k. or greater Controls.............................................. Pedal switch, LEVEL knob, LOW DIST knob Indicat...