Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
When connecting the mains lead to a plug, be sure to connect each conductor to the correct terminal, as indicated. "This instruction applies to the product for United Kingdom.' MAINS LEADS PLUG Conductor Color Mark on the matching terminal Live Brown Red or letter L Neutral Blue Black or letter N Grounding Green* Yellow Green, Green*Yellow, letter E or symbol For Canada CLASS B NOTICE This cfigitai apparatus does not exceed the Class B limits for radio noise emissions set out in the Radio interference Regulations of the Canadian Department of Communications. üLASSE B AVIS Cet appareil numérique ne dépasse pas les limites de la classe B au niveau des émissions de bruits radio-électnques fixés dans le Règlement des signaux parasites par le ministère canadien des Communications Bescheinigung des Hnsnllen /Importeure Hiermit wird bescheinigt, daß der/die/d« ROLAND MICRO .COMPOSER MC-SOOMKII (Gaut. Typ. in Übereinstimmung mit den Bestimmungen üer Amisbl. Vfg 1046 / 1984 lAmiiimiiwuMwinqi funloentstort ist. Der Deutsehen Bundespost wurde das Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung der Serie aut Einhaltung der Bestimmungen eingeraumt. Roland Corporation Osaka / Jaoan Nm o*i MmiMmiMwHM« Please read the separate ualurne "MIDI", before reading this owner's manual Copyright © 1988 Jay ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in snv form without the written oermission of ROLAND CORPORATION! ÄRoland ■Ml M1CRD CDMPDSER K/IC-SDOmkIE Hardware Manual ■ IMPORTANT NOTES Power • The appropriate power supply for this unit is shown on its name plate. Please make sure that the line voltage in your country meets the requirement. • Do not use the same socket used for any noise generating device, or any device that may consume large amounts of power. • This unit might not work properly if plugged into the wall socket while switched on, or if tunred on immediately after being turned off, and so on. If this happens, turn the unit off, then turn it on again after waiting for a few seconds. • It is normal for this unit to become hot while being operated. • To avoid damaging a power cable or causing a short circuit, be sure to hold the plug when disconnecting the cable from a wall socket. If the unit is not to be used for a long period of time, be sure to disconnect the power cable from the wall socket. Location • Do not place the MC-500MKII in any of the following locations. Malfunctions may result if it is placed where: o there is excessive heat (in direct sunlight, beside or on a heater, etc.) o there is excessive humidity o there is a lot of vibration • Do not leave the MC-500MKI1 where it is exposed to direct sunlight or inside a ciosed car for a long period of time. Excessive heat could cause the cabinet to warp. • Avoid placing the MC-500MKII near a neon or fluorescent light or near a cathode ray tube (television or computer display) because these devices generate noise. • Do not place or drop anything heavy on the main unit or its power cable because this could damage either of these. Cleaning • Use a soft cloth and clean only with a mild detergent. • Do not use solvents such as paint thinner or alcohol. Miscellaneous • Never put foreign matter (a coin, a wire, etc.) into the MC-500MKII. Never spilt liquids (water,* soft drinks, liquor, etc.) onto it either. • Never push or hit the display. Place this unit in a steady, horizontal place. Note on handling the floppy disk drive • The built-in disk drive of MC-500MKII is a precision machine. So, Please handle it gently. Especially while the Disk Drive is running, do not give a strong shock to the unit. • The floppy disk's hard plastic case conceals a thin disk of plastic film coated with a magnetic medium. Always handle with care because the slightest damage to this high-density recording medium can mean irretrievable loss of data. • Disks could also become erased naturally after a certain length of time. To ensure a long life for your data disks, be sure to follow the instructions. • Handling the floppy disk properly will maximize its life time. It, however will be erased some day in the course of nature. Please be sure to copy the system disk onto the supplied or a brand new disk and preserve the original system disk safely. • We recommend that you make a few copies of your important data. • Remove the disk from the disk drive before turning on or off the unit. • Please do not touch the magnetic film, or the disk may become damaged. • Please do not touch the shutter that covers the magnetic film. The magnetic field can be easily damaged, even by slight amount of grease. • Please insert the disk securely into the disk drive. When removing the disk, push the Eject Button until it clicks. If the disk has stuck in the disk drive, do not attempt to remove it but push the Eject Button, and it will come out without any trouble. • Never r...