Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Increasing this value will increase the distortion. No Parameter Value Description 1 Pre Filter Type 0-5 1-6 Selects the type of filter applied to the sound before it passes through the Lo- Fi effect. 2 LoFi Type #1 0-8 1-9 Degrades the sound quality. The sound quality grows poorer as this value is increased. 3 Post Filter Type 0-2 Off, Lpf, Hpf Type of filter Off: no filter is used Lpf: cuts the frequency range above the Cutoff Hpf: cuts the frequency range below the Cutoff 4 Post Filter Cutoff 0-16 200-8000 Hz Basic frequency of the Post Filter 5 Low Gain 0-30 -15 - +15 dB Gain of the low range 6 High Gain 0-30 -15 - +15 dB Gain of the high range 7 Balance #2 0-100 D100:0W D0: 100W Volume balance between the direct sound (D) and the effect sound (W) 8 Level 0-127 0-127 Output level 28 .. No Parameter Value Description 1 Voice Quality #1 0-15 0-15 Audio quality of the telephone voice 2 Treble 0-30 -15 - +15 dB Bandwidth of the telephone voice 3 Balance #2 0-100 D100:0 D0: 100W Volume balance between the direct sound (D) and the effect sound (W) 4 Level 0-127 0-127 Output level . 0156: Gate Reverb This is a special type of reverb in which the reverberant sound is cut off before its natural length. No Parameter Value Description 1 Type #1 0-3 Normal, Reverse, Sweep1, Sweep2 Type of reverb Normal: conventional gated reverb Reverse: backwards reverb Sweep1: the reverberant sound moves from right to left Sweep2: the reverberant sound moves from left to right 2 Pre Delay 0-125 0.0-100.0 ms Adjusts the delay time from the direct sound until the reverb sound is heard. 3 Gate Time 0-99 5-500 ms Adjusts the time from when the reverb is heard until it disappears. 4 Low Gain 0-30 -15 - +15 dB Gain of the low range 5 High Gain 0-30 -15 - +15 dB Gain of the high range 6 Balance #2 0-100 D100:0W D0: 100W Volume balance between the direct sound (D) and the reverb sound (W) 7 Level 0-127 0-127 Output Level . 0200: Overdrive>Chorus This effect connects an overdrive and a chorus in series. No Parameter Value Description 1 Overdrive Drive 0-127 0-127 Degree of distortion Also changes the volume. 2 Overdrive Pan 0-127 L64 - 63R Stereo location of the overdrive sound 3 Chorus Pre Delay 0-125 0.0-100.0 ms Adjusts the delay time from the direct sound until the chorus sound is heard. 4 Chorus Rate Mode 0-1 Hz, note When this is set to “note,” the effect is synchronized with the tempo. 5 Chorus Rate #1 1-127 0.05 - 10.00 Hz Frequency of modulation (Hz) 6 Chorus Rate 0-21 note Frequency of modulation (note) 7 Chorus Depth 0-127 0-127 Depth of modulation 8 Chorus Balance #2 0-100 D100:0W D0: 100W Adjusts the volume balance between the sound that is sent through the chorus (W) and the sound that is not sent through the chorus (D). 9 Level 0-127 0-127 Output Level . 0201: Overdrive>Flanger This effect connects an overdrive and a flanger in series. No Parameter Value Description 1 Overdrive Drive 0-127 0-127 Degree of distortion Also changes the volume. 2 Overdrive Pan 0-127 L64 - 63R Stereo location of the overdrive sound 3 Flanger Pre Delay 0-125 0.0-100.0 ms Adjusts the delay time from when the direct sound begins until the flanger sound is heard. 4 Flanger Rate Mode 0-1 Hz, note When this is set to “note,” the effect is synchronized with the tempo. 5 Flanger Rate #1 1-127 0.05-10.00 Hz Frequency of modulation (Hz) 6 Flanger Rate 0-21 note Frequency of modulation (note) 7 Flanger Depth 0-127 0-127 Depth of modulation 8 Flanger Feedback 0-98 -98 - +98% Adjusts the proportion of the flanger sound that is fed back into the effect. Negative (-) settings will invert the phase. 9 Flanger Balance #2 0-100 D100:0W D0: 100W Adjusts the volume balance between the sound that is sent through the flanger (W) and the sound that is not sent through the flanger (D). 10 Level 0-127 0-127 Output Level . 0202: Overdrive>Delay This effect connects an overdrive and a delay in series. No Parameter Value Description 1 Overdrive Drive #1 0-127 0-127 Degree of distortion Also changes the volume. 2 Overdrive Pan 0-127 L64 - 63R Stereo location of the overdrive sound 3 Delay Mode 0-1 ms, note When this is set to “note,” the effect is synchronized with the tempo. 4 Delay Time 0-127 0 - 2540 ms Adjusts the delay time from the direct sound until the delay sound is heard. (Hz) 5 Delay Time 0-21 note Adjusts the delay time from the direct sound until the delay sound is heard. (note) 6 Delay Feedback 49-89 0 - +80% Adjusts the proportion of the delay sound that is fed back into the effect. 7 Delay HF Damp 0-17 200-8000 Hz, Bypass Adjusts the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies, set this parameter to Bypass. 8 Delay Balance #2 0-100 D100:0W D0: 100W Adjusts the volume balance between the sound that is sent through the delay (W) and the sound that is not sent through the delay (D). 9 Level 0-127 0-127 Output Level . 0203: Distortion>Chorus The parameters are essentially the same as in “Overdriv...