Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
To make the best use of the unit, please read the instructions carefully. -Despite its compact size, this effect unit can put out a rich and truly powerful distortion sound which can be sustained for very long durations. -Two specially designed Color Mix controls provide for wide-ranging tone control. -Whether for solos or for backing, it makes possible a well-balanced new-age metal sound. urn-3 HVPGR metal LEVEL COLOR MIX ÜIST OUTPUT INPUT <- HIVPeR metal htm-3 r-PANEL DESCRIPTION IfVEL COLOR UIX PiST D Q Q O OUTPUT INPUT <- HVPGR metal Hm-3 OK3DS5 8 9 10 t AC Adaptor Jack Connect an AC adaptor ( BOSS PSA-120, 220 or 240 depending on the line voltage system in your country ) to this jack. * An AC adaptor allows long and secure operation without worrying about battery life. * Be sure to use a BOSS PSA-120, 220 or 240 adaptor.Use of any other adaptor may damage the device. 2 Check Indicator Lights up when the effect is ON, allowing you to confirm whether the effect is ON or OFF. * This indicator also serves as the Battery Check indicator. You will know when the battery has worn down and needs to be replaced whenever this indicator goes dim or no longer lights. 3 Level Knob Used to adjust the volume level of the sound while the effect is applied. Should be adjusted so there is no noticeable difference between the times when the effect is applied and when the sound is normal. * With this knob turned all the way to the left, no sound will be output. 4 Color Mix Low Knob Allow the lower frequency portions to be boosled/cut. At the center, the tone will be flat. Boost the lower frequencies by turning it towards the right (). Turn toward the left (, ■) to cut them. 5 Output Jack The output from this jack can be connected to your amp or to another effects device. I—CONNECTIONS i... Amplifier Conned the AC Adaptor output input <- HVPGR metal Hm-3 OI3DSS v r AC Adaptor: BOSS PSA-1 2U, 220 or 240 {option) A m T mrniim Guitar Inserting a plug into the Input tack will automatically switch (he unit on. Before connecting or disconnecting a plug, make sure that (he volume of the amplifier is turned dovvn. 6 Pedal Switch Used to switch the effect ON or OFF. 7 Thumb screw Loosen the screw to open the cover for battery replacement. For a detailed explanation, see "BATTERY REPLACEMENT" 8 Distortion Knob Used to adjust the depth of the distortion. The distortion depth is increased (and sustains will be lengthened) as you move the knob to the right (■ '*). * Oscillation could be produced if the depth is increased too much. 9 Color Mix High Knob Allow the higher frequency portions to be boosted/cut. At I he center, the tone will be flat. Boost the higher frequencies by turning it towards the right (»<). Turn toward the left (.') to cul (hem. 10 Input Jack Here is where you need to connect your guitar, or other electric/electronic instrument. * The Input fack is equipped with a power switch. Whenever you insert a plug into it, the power is turned ON. Pull the plug out, and the power goes OFF. For this reason, try to make a habit of pulling out the cord going to the Input lack whenever the pedal is not being used. OPERATION 1 Once you have all the connections made, set the knobs on the panel so they conform lo the illustration below. * Before connecting or disconnecting any instrument, make sure that the volume of the amplifier is turned CHECK 0 LEVEL COLOR MIX HST MM MAX CUT BOOST cm BOOST MM MAI LOW HIGH 2 Step on pedal switch (6) lo turn ON the effect. (The Check indicator will light.) check O LEVEL COLOB MIX «ST QQQ MM MAX CUT BOOST CUT BOOST MW MM LOW HIGH 3 Use the Distortion knob (8) to adjust the depth of the distortion. The distortion depth is increased as you move the knob to the right. * Oscillation could be produced if the depth is increased too much. 4 Adjust both the low and high Color Mix knobs (4 & 9) until you have the tone you desire. CHECK 0 L£Va COLOR MIX DtST uni MAI OIT BOOST CUT BOOST MM MAX LOW NIGH 5 Adjust the Level Knob (3} so there is no noticeable difference between the limes when the effect is applied and when the sound is normal. vvrwn DU U19 I 000 SAMPLE SETTINGS Hyper Metal Sound A futuristic metallic sound that is really thick, yet behaves well. Hard Rock A distorted sound with well-balanced low and high ranges. CHECK O LEVEL COLOR MIX DIST MIN MAX CUT BOOST CUT BOOST MIN MAX LOW HiGH Heavy Metal These settings are radical both the low and high ranges get pushed out in front. Warm Drive A warm and mild sound. CHECK O LEVEL COLOR MIX DIST MIN MAX CUT BOOST CUT BOOST MIN MAX LOW HIGH Slash Metal Hyper Rock Sound A sound with a biting edge {hat doesn't get muddled even when used with fast-tempo backing. An almighty sound with emphasis placed on the midrange. CHECK o COLOR MIX MIN MAX CUT BOOST CUT BOOST MIN MAX LOW HIGH CHECK o COLOR MIX MEN MAX CUT BOOST CUT BOOST LOW HIGH O...