Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
This setup will prevent unnatural break of the reverberation type effect. Effect Turns the noise suppressor effect on/off. Threshold Adjust this parameter as appropriate for the volume of the noise. If the noise level is high, a higher setting is appropriate. If the noise level is low, a lower setting is appropriate. Adjust this value until the decay of the guitar sound is as natural as possible. * High settings for the threshold parameter may result in there being no sound when you play with your guitar volume turned doivn. Release Adjusts the time from when the noise suppressor begins to function until the volume reaches "0." < FV (Foot Volume)> Level This adjusts the volume. Control with the Foot Volume To control the volume of the foot volume with the Expression pedal, set "Setting the Expression pedal" (page 24) as follows. * You can also use the control assign. < Quick Settings > EXP PEDAL: Pl=FOOT VOLUME < Manual Settings > EXP PEDAL: On EXP PEDAL Target: FV: Level EXP PEDAL Target Min: 0 EXP PEDAL Target Max: 100 &coo«$c9ee&eo9dS{«e&»c«ea«A»coa9ocesoQ№C'0'e 57 Section 4 Using MIDI How MIDI can be used_ On the GT-3 you can use MIDI to perform the following operations. * MIDI requires you to set the channel numbers of the two devices to be connected to the same number. If the MIDI channels are not matched correctly, the data cannot be communicated between the tivo MIDI devices. Operation from the GT-3 < Transmitting program change messages > When a patch is selected on the GT-3, the program change message that corresponds to the selected patch number will be transmitted. The external MIDI device will then turn to the setting depending on the program change it has received. 0-0 I—4 aaaao a a a f Operations from external MIDI devices < Select patches > The patch numbers on the GT-3 will change in keeping with the program change messages sent to it from an external MIDI device. You can set up the correspondence between MIDI program change messages and patch numbers on the GT-3 with the "Program change map" (page 63), if you wish to make the effect sounds correspond to the sounds on some other MIDI device. The setup shown below is for playing the guitar to a sequencer's playing. If you wish to automatically change patches on the GT-3, place the program change number that corresponds to the relevant patch together with the performance data at the position where you wish to change patches on the GT-3. aeoDD oa no oaaoD do aao oa OQQ OOOC3 aa oao I MIDI OUT MIDI IN аадн ~B§S ÍÉSW ff ft л < Transmitting control change messages > The operation information from the CTL pedal, Expression pedal or the external device connected to the SUB EXP PEDAL/SUB CTL 1,2 jack will be transmitted as control change messages. This can be used for controlling the parameters on the external MIDI device. < Receiving control change messages > Through MIDI, the GT-3 is able to receive control change messages and control specified parameters during live performance. Set the parameters to be controlled with "Control assign" (page 26). < Transmitting data > You can transfer the setting data stored in the GT-3, such as an effect sound to another MIDI device using the Exclusive messages. This can be convenient for setting the other GT-3 to exactly the same settings or store the effect sound settings into a sequencer. < Receiving data > Here's how to receive data transmitted from another GT-3, or receive GT-3 data that was saved on a sequencer. 58 Section 4 Using MIDI MIDI utility function settings The following pages explain the MIDI-related utility functions of the GT-3. Make settings as needed for your situation. The following utility functions are provided. [MIDI RX Channel (MIDI receive channel)] [MIDI Omni Mode] [MIDI TX Channel (MIDI transmit channel)] [MIDI Device ID] [MIDI PC OUT (MIDI program change out)] [MIDI EXP OUT (MIDI Expression pedal out)] [MIDI CTL OUT (MIDI Control pedal out)] [MIDI SUB CTLIOUT (MIDI sub control 1 out)] [MIDI SUB CTL20UT (MIDI sub control 2 out)] [MIDI Map Select] [MIDI Program Map (MIDI program change map)] [MIDI Bulk Load] [MIDI Bulk Dump] [Procedure] * When using the following functions, please refer to the procedure given for each function. [MIDI Bulk Dump] [MIDI Bulk Load] [MIDI Map Select] [MIDI Program Map (MIDI program change map)] 3 I 5 2 1 1. Each time you press [UTILITY], the following items will appear in succession. Call up the MIDI-related items on the display. * While utility function settings are being made, the button indicator will be lit. <1. GLOBAL > < 2. METER > < 3. SYSTEM > < 4. MIDI > — UTILITY --- 4,MIDI_ Make settings for operation via MIDI. < 5. HR SCALE (harmonist scale) > < 6. AR PHRASE (auto riff phrase) > 2. Get the display to show the parameter to be controlled, using [PARAMETER]. If more than one parameter is shown in the display, move the cursor to the parameter to be edit...