Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Please follow the instructions indicated in the message to resolve the issue. “MIDI BUFFER FULL” “USB BUFFER FULL” . The data cannot be processed correctly due to the high volume of MIDI messages. . Reduce the volume of MIDI messages transmitted to the GT-10. “MIDI OFFLINE” “USB OFFLINE” . Transmissions from the connected device have been interrupted. This message also appears when the power to the connected device has been turned off. It does not indicate damage. . Check to make sure no cable is disconnected and that there are no shorts. “DATA WRITE ERROR” . Writing to the memory for storage of user data failed. . The unit may be damaged. Consult the nearest Roland service center. If there is no sound or other operational problems occur, first check through the following solutions. If this does not resolve the problem, then contact your dealer or a nearby Roland service station. Problems with the sound No sound / volume too low . Are the connection cables broken? > Try using a different set of connection cables. . Is the GT-10 correctly connected to the other devices? > Check connections with the other devices (p. 22). . Is the connected amp/mixer turned off, or the volume lowered? > Check the settings of your amp/mixer system. . Is the OUTPUT LEVEL knobs lowered? > Adjust the OUTPUT LEVEL knobs to an appropriate position (p. 24). . Is Tuner set to On? > When the volume is set to “Mute” in the Tuner mode, even the direct sound will not be output by setting the Tuner to “On” (p. 28). . Is each effect set correctly? > Use the “Changing the Connection Order of Effects (Effect Chain)” (p. 38) to check the output level of each effect. If there is an effect for which the meter does not move, check the settings for that effect. . Is “USB/DGT Out Lev” set to a low value? > Adjust the setting to an appropriate value (p. 135). . Is “PEDAL: FV: Level” or “MASTER: Patch Level” specified as an assign Target? > Move the controller to which it is assigned. . Is the power to the external device connected to the EXT LOOP jack off, or is the volume of the device turned down? > Check the settings for the connected device. Sound from devices connected to the INPUT jack is not heard in the headphones . Is the Dir.Monitor (p. 93) set to OFF? > Set to ON. Appendices 145 Appendices Appendices . Could you be using a connection cable that contains a resistor? > Use a connection cable that does not contain a resistor. Oscillating sound occurs . Is the value for any gain- or volume-related effects parameter set too high? > Lower these values. . Is the INPUT SELECT (p. 61) set to “USB In?” > When set to “USB In,” audio signals may, depending on the software settings, end up looping. You can use the following methods to prevent this from happening. • Stop playback with the software, and set Soft Thru to Off. • Switch the software’s audio input off. • Change INPUT SELECT to “Guitar 1–3.” No change in preamp tone even after switching patches . Has the GT-10 been set to “System1–3” in Preamp mode (p. 69)? > When the GT-10 is set to “System1–3” in Preamp mode, the preamp settings do not change when patches are switched. To make different preamp settings for individual patches, choose the “Patch” setting in Preamp mode. Unable to change parameters with the knobs or dial . Are you using the Internal Pedal System (p. 54) in Assign? > When the Assign Source is set to “INTERNAL PDL” or “WAVE PDL,” the effect parameter set as the Assign Target changes automatically. If you want to be able to change the parameters manually with the knobs and dial, first switch off Assign to deactivate the Internal Pedal System. . Is “INPUT LEVEL” (p. 50) set as the Assign Source in Assign? > When “INPUT LEVEL” is set for the Assign Source, the effect parameter set as the Assign Target changes automatically according to the level of the input from the guitar (the playing dynamics). If you want to be able to change the parameters manually with the knobs and dial, first switch off Assign. Other Problems Patch does not change . Is something other than the Play screen shown in the display? > On the GT-10, patches can be selected only when the Play screen is displayed. Press [EXIT] to return to the Play screen (p. 24). Parameters specified with Assign can’t be controlled . Could the effect be switched off? > To control a parameter using the EXP Pedal or footswitch, make sure the effect that contains the parameter you intend to control is switched on. . Is Prefernc ("preference") for Pedal Function set to the "System" setting? > Even when an assignment setting has been made for the patch, the setting made for Pedal Function (p. 47) takes precedence. To enable the setting made for the patch, for Pedal Function set the preference for the relevant controller to Patch. . Do the MIDI channel settings of both devices match? > Make sure that the MIDI channels of both devices match (p. 80). . Do the controller number settings of both devices match? > Make sure that the controll...