Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
OPERATION IS SUBJECT TO THE FOLLO THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, 1NCLUD 8 POWER ON Once the connections have been completed (p. 8), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. Ensure that all connections are correct and secure. Turn the GFC-50's Power switch to the ON or ECONOMY position. Turn on the other devices. When the GFC-50 is being operated with batteries, the Economy mode can be used to effectively extend battery life by about twice as long as usual. The Bank Display may become somewhat dimmer and it may flicker a little, but this is not an indication of a problem. * The default MIDI channel of the GFC-50 is channel 1. Refer to "CHANGING MIDI CHANNEL" (p. 13) if you want to change the default setting. POWER ECONOMY °N—I I {-OFF ■ ■ About the Economy Mode 9 PROGRAM CHANGE NUMBERS A Program Change number is selected using the "Bank" button and "Number" pedals. The Program Change message is transmitted the moment the Bank Shift button or Number pedal is pressed. Changing Banks_ Pressing a Bank Shift button (UP or DOWN) changes Bank numbers in sequence (0 to 12). The Bank Display shows the Bank Number currently selected. Display n u i i E T7 U * 1 1 ? Banks 0 1 2 10 11 12 * When Bank 10,11 or 12 is selected, the Dot in the upper left hand corner of the display will light. Bank numbers 0 to 12 correspond to Program Change numbers as indicated in the following: Banks 0 1 2 10 11 12 Program Change Number 0 10 20 100 110 120 You can change Bank numbers using a pedal by connecting a foot switch (BOSS FS-5U: optional) to the BANK SHIFT Jacks (UP/DOWN) on the rear of the GFC-50. When using the FS-5U, set the polarity switch as shown below. jn^-Lu =1 Polarity switch Changing Numbers_ Using the Number Shift (A/B) Pedal and the Number Pedals, you can select numbers 1 to 10. Numbers 1 to 10 correspond to Program Change numbers 1 to 10 respectively. By selecting A or B with the Number Shift Pedal, you can select numbers 1 to 5 or 6 to 10 as shown below. 1/6 2/7 3/8 4/9 5/10 A 1 2 3 4 5 B 6 7 8 9 10 With the Number Indicators and Number Shift Indicators, you can determine what number is currently set. 10 PROGRAM CHANGE NUMBERS Setting a Program Change Number Example 1: Setting Program Change number 8. 0 (Bank: 0) + 8 (Number) = 8 Example 2: Setting Program Change number 12. 10 (Bank: 1) + 2 (Number) = 12 Example 3: Setting Program Change number 120. 110 (Bank: 11) + 10 (Number) = 120 * The highest Program Change number is 128. Setting a number higher than 128 will cause the Pedal Indicators to flash, indicating that no Program Change message is being transmitted. 11 CONTROL CHANGE MESSAGES The GFC-50 can accept connection of a maximum of two external expression pedals (Roland EV-5: optional) and two foot switches (BOSS FS-5L/FS-5U: optional). This allows you to control a connected MIDI instrument in real time with Control Change messages. The Control Change jacks on the rear of the GFC-50 correspond to the following Control Change numbers: Expression Pedal EXP 1: Volume (#7) EXP 2: General Purpose Controller (#16) Control Peal CTL 1: Hold (#64) CTL 2: General Purpose Controller (#80) * "#" represents a Control Change number. Set the polarity switch as shown below. CTL 2 CTL 1 Foot switch FS-5L (BOSS) or FS-5U (BOSS) EXP 2 EXP 1 (VOLUME) Roland ev-s Roland EV-S \ - '/ \ \ \ \ \ \ \ \ \ \ \ \ \ * \ \ \ * \ s '/ s \ * \ * s * '/ \ t s \ \ * \ \ t \ \ * \ * \ * \ f s f s t \ \ * \ * \ s t \ \ \ * \ Expression Pedal EV-5 (Roland) * Either a latch-type (FS-5L), or momentary-type (FS-5U) footswitch can be connected to each CTL Jack. Latch Type: Pressing the pedal turns a connected unit (or function) ON or OFF. Momentary Type: Only while the pedal is being pressed, the ON/OFF status can be changed. Use only the specified expression pedal (EV-5; sold separately ). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit. 12 CHANGING MIDI CHANNEL The GFC-50's default MIDI channel is channel 1. If you wish to change the default channel, follow this procedure: * The MIDI channel you set will not be stored in memory. It will be necessary to set the MIDI channel each time the unit is turned on. 1. Switch on the unit while holding the Number Shift Pedal (A/B) down. 2. Select the desired MIDI channel using the Bank Shift Buttons (UP/DOWN). (The Bank Display shows the MIDI channel currently selected.) Display / i S 3 ТП и • i i ? Б MIDI CHANNEL 1 2 3 10 11 12 16 * When any of MIDI channels 10 to 16 is selected, the Dot in the upper left hand corner of the display will light. 3. Press the Number Shift Pedal (A/B). (The MIDI channel has now been set.) 13 BATTERY REPLACEMENT When to replace th...