Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
* When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible. Changing the Battery When the indicator goes dim or no longer lights while the effect is on, it means that the battery must be replaced. Replace the battery following the steps below. 1. Hold down the pedal and loosen the thumbscrew, then open the pedal upward. * The pedal can be opened without detaching the thumbscrew completely. 2. Remove the old battery from the battery housing, and remove the snap cord connected to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery’s polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, and then close the pedal. * Carefully avoid getting the snap cord caught in the pedal, coil spring, and battery housing. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely. Troubleshooting Power won’t come on / CHECK indicator doesn’t light: .. Is your guitar properly connected to the INPUT jack? Check the connection once more. * The power will not turn on without a plug connected to the INPUT jack. * The CHECK indicator shows whether the effect is being applied or not. It does not indicate whether the power to the device is on or not. .. Is the specified adaptor (PSA series: optional) properly connected? Check the connection once more. * Never use any AC adaptor other than one specified for use with the FRV-1. .. Is the battery low or dead? Replace with a new battery. * The battery that is supplied with the unit is for temporary use, intended primarily for testing the pedal’s operation. * If you’ll be using the FRV-1 for an extended time, we recommend that you use an AC adaptor. If you prefer to use a battery, we recommend an alkaline battery. * To prevent unnecessary battery consumption, be sure to disconnect the plug from the INPUT jack when not using the effects unit. No sound / Low volume: .. Is your instrument properly connected to the FRV-1? Check the connection once more. .. Is the DWELL knob and/or MIXER knob turned down? Turning the DWELL knob or MIXER knob toward the left will decrease the amount of reverb sound when the effect is on; if either knob is turned all the way to the left, there will be no reverb sound. To hear the reverb, turn the DWELL knob and MIXER knob to the right. .. Is the volume turned down on any guitar amp or effects device you have connected? Check the settings of the connected device. .. Is the battery low or dead? Replace with a new battery. “Springy,” “twangy,” or “drip-like” sounds are heard in the reverb: In the original Fender Reverb, these sounds are produced by the mechanical resonances of the springs. They are apparent as the DWELL knob is turned up, and also when dynamic, percussive sounds are played into the unit. These sound characteristics are particularly popular in surf guitar music, and are an integral part of the genre. As with the other characteristics of the Fender Reverb, the FRV-1 faithfully models these resonance sounds. Turning the DWELL knob to the left will reduce their level and create more of a “room” reverb sound. Setting Samples Surf Sound Blues Sound Specifications FRV-1: Fender Reverb * 0 dBu = 0.775 Vrms * The battery that was supplied with the unit is for temporary use, intended primarily for testing the unit’s operation. We suggest replacing this with an alkaline dry cell. * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice. * FENDER®, STRATOCASTER®, TWIN REVERB®, and the distinctive headstock and body design commonly found on the STRATOCASTER guitar are the trademarks of FMIC. All rights reserved. In this document, their names are used solely to identify the equipment whose sound is simulated by COSM. AC Adaptor (PSA series: optional) Guitar Amplifier Electric Guitar If you use an overdrive or distortion-type effect, we recommend that you connect it before the FRV-1. As an alternate connection method, you can insert the FRV-1 in your guitar amp’s serial effect loop (send/return) if it is equipped with one. This is recommended if you’re using your amp’s preamp section to generate high-gain distortion sounds. Refer to the owner’s manual for your amp to learn more about using its effect loop. The result of a collaboration with Fender®, the FRV-1 is a compact pedal that uses COSM technology to faithfully reproduce the sound of the classic Fender Reverb unit. (Composite Object Sound Modeling) Composite Object Sound Modeling—or “COSM” for short—is BOSS/ Roland’s innovative and powerful technology that’s used to digitally recreate the sound of classic musical instruments and effects. COSM analyzes the many factors that make up the original sound—including its electrical and physical characteristics—and creates a digital model that accurat...