Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Empty steps are indicated by “- - - -” when [EXIT] is pressed in the Song screen. Chapter 8 Creating and Performing Songs ([SONG]) 3. Press [ENTER] to determine the pattern to be recorded. The measure numbers advance automatically. The asterisk (*) indicates that the pattern displayed has not been confirmed. If you press [EXIT] at this point, the pattern that has already been set appears in the display. If no pattern has been confirmed, “- - - -” is displayed. Once you confirm the pattern, the asterisk disappears. 4. Press [ ] [ ] to change the step to be recorded. 5. Repeat Steps 2–4 as needed to record the data for the song. 6. To stop recording, press STOP [ ]. The STEP REC [ ] goes out. * Note that pressing START [ ] during Step Recording (while STEP REC [ ] is lit) switches the DR-3 to Realtime Recording. Erasing Previously Recorded Sounds As You Continue Recording You can use the following procedure to delete the displayed pattern. 1. Press [ ] [ ] to display the pattern to be deleted. 2. Hold down STEP REC [ ] and press [ENTER]. The pattern is deleted, and the subsequent patterns are shifted forward. ¦ When Using Realtime Recording The sounds are recorded as the patterns are switched with the pads. * When recording over a song that has already been recorded, the newly recorded data overwrites the previously recorded data, which is discarded. Make sure you have pressed [SONG] to switch to Song mode. 1. Hold down STEP REC [ ] and press START [ ]. 2. Turn the VALUE dial to select the style, and press a pattern pad to specify the first pattern to be recorded. Recording begins from the pattern specified. The Song Recording screen appears. Measure Pattern Name Style No.Song No. 3. Perform by switching the patterns with the pattern pads. Perform exactly as in Style Manual mode (p. 43). The ON/OFF status of the VARIATION [PTN], [KIT] and [MUTE] (p. 45) is also recorded. You can also change styles by turning the VALUE dial. * If you switch the style during its performance, a “ ” mark appears in front of the style name which will be played next. The style switches after the currently playing pattern ends, and the “ ” mark disappears. * The ON/OFF status of the VARIATION buttons and fill-ins can be recorded only in a unit of pattern. 4. When you press [ENDING/STOP], the ending is played, and then both the performance and the recording stop. If you want to stop the recording immediately, press STOP [ ]. Chapter 8 77 Chapter 8 Creating and Performing Songs ([SONG]) Substituting Recorded Patterns When you record using Realtime Recording into a song that already has material recorded in it, the patterns in the segment in which you record are overwritten, allowing you to replace them with the new patterns. 1. With the performance stopped, press [ ] [ ] to select a measure slightly ahead of where you want to record. 2. Hold down STEP REC [ ] and press START [ ]. The prerecorded pattern starts to play. 3. When you reach the measure before the one you want to substitute, select the next pattern to be recorded. 4. To stop recording, press STOP [ ]. The previously recorded pattern data after the point where you stop the recording remains unchanged. ¦ Editing Notes to Drum Parts and Bass Parts in the Song You can use Realtime Recording to add and edit notes to drum and bass parts in songs you have recorded. When editing sounds, begin recording from a point slightly before the point where you want to edit the sounds. * You cannot record notes into empty songs that contain no recorded data. * The performance recorded here is only stored in the song as exclusive patterns. The edited notes are not reflected in performances of patterns in Style Play mode (when [MANU] or [AUTO] is lit). Additionally, changing patterns in Style Play mode has no effect on the songs. * You can have up to 100 exclusive patterns for all of the songs. Make sure you have pressed [SONG] to switch to Song mode. 1. With the performance stopped, press [ ] [ ] to select a measure slightly ahead of where you want to record. 2. Press STEP REC [ ]. The Song Recording screen appears. 3. Press [INST]. A massage screen is displayed. 4. Press [INST] to select the sound group to be recorded. Displayed Group Name DRUM Drum Set PERC Percussion BASS Bass BASS The bass sound one octave lower BASS The bass sound one octave higher Chapter 8 Creating and Performing Songs ([SONG]) 5. Turn the VALUE dial to set the quantization. This corrects mistakes in the rhythm played to the closest selected note value. Display Description Description – – Off. Sounds are recorded without quantization, with the same timing used in tapping the pads. 32th note 16th note triplets 16th note 8th note triplets 8th note 6. Press START [ ]. STEP REC [ ] lights up, START [ ] flashes, and the metronome begins playing. 7. Record the performance, pressing the pads while following the rhythm provided by the metronome. The force used to tap the pads is recorded as velocity (the strength or stress of ...