Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet. Should you remove screws, cord clamps, or stabilizer, make sure to put them in a safe place out of children’s reach, so there is no chance of them being swallowed accidentally. ■ Check the Parts Secure the right side board to the speaker box with the attachment screws (M6 x 20 mm, in two places). Attach so that the speaker cable at the rear of the speaker box is directed to the left. Side board right|Front Before you begin assembling the DP-990, check that all the parts were supplied. You will also need to have a Phillips screwdriver. Side board (left) Speaker box Attachment screw Speaker cable (rear) Secure the left side board to the speaker box with the attachment screws (M6 x 20 mm, in two places). Speaker box Side board left Stabilizer (left) Pedal Board Stabilizer (right)'— Side board (right) 1: Attachment screw (M6 x 20 mm) x 8 2: Stabilizer screw (M4 x 16 mm) x 6 3: Cord clamp x 2 The speaker box can also be installed so that it faces toward the rear instead of toward the front. Having the speaker box face out the rear of the instrument allows the speakers to be directed toward listeners when the back of the instrument faces the audience. Raise the entire assembly. When standing the assembled unit up, grasp near the speaker box, and gently raise the assembly. Normal direction When facing to the rear Set the stabilizer in the holes in the side boards (M4 x 16 mm, in six places). Speaker box Assembly Procedure At first, assemble the entire unit in a temporary fashion, without really tightening the screws. Then, after checking the overall alignment of the boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws. Be careful when assembling the DP-990, so as to avoid scratching the parts. Stabilizer screws — Take care not to attach the left and right stabilizer to the wrong sides. 5. Put the Pedal Board on the stabilizer. When putting the Pedal Board on the stabilizer, first loosen the attachment screws securing the speaker box to the side boards. 9. Connect the speaker cable extending from the rear of the speaker box to the DP-990’s speaker connector. Press the speaker cable completely into the connector so that it is securely fastened. Putting the Pedal Board [a lateral view) Pedal Board Pedal Board X Metal Parts Speaker cable — r. Hold and insert the cable so that the clip portion extends into the stand and is securely connected. DP-990 Rear Speaker Connecter 6. Secure the Pedal Board to the side boards with the attachment screws (M6 x 20 mm, in two places). Retighten the screws loosened in Step 5. Use the speaker cable with the ferrite core left attached to the cable. The DP-990 cannot be used with the ferrite core removed. 10. To stabilize the pedals Temporarily loosen the screws that fasten the pedal board. Step on the pedal, and after verifying that the pedal is in firm contact with the floor, re-tighten the attachment screws firmly. 7. Align the protruding screws (one each at right and left) on the bottom of the piano with the openings in the metal fittings on the side board, then slide the piano forward until the screws are held in place. * When handling the piano, firmly grasp it at the front and back. Be careful, so you do not get your fingers pinched. Place the keyboard so that it is centered, both front to back and left to right. 8. Fasten the piano to the stand with the attachment screw (M6 x 20 mm) (one each for the right and left). Copyright © 2007 ROLAND CORPORATION DP-990 All rights reserved. No part of this publication may be reproduced in any 11. As necessary, affix cord clamps as shown in the diagram to fasten the pedal cable. When Moving the Instrument Disconnect the power cord and cables from the DP-990. Then lift the piano while keeping it level, and move it with care, so that you do not drop it on your feet, or get your hands caught. Check the stability of the pedal, and make adjustments as necessary. When Disassembling Disassemble the unit by carrying out assembly Steps 1-11 in reverse order. When Changing the Orientation of the Speaker Box Be sure to completely disassemble the unit, change the speaker box orientation, then reassemble it. 40782734-01 40782734 1PD without the written permission of ROLAND CORPORATION. Connect the pedal cable to the Pedal jack. 40782734-01 mom&iLZt'll: (DP-990) QA о * Æ TfEÜt2Лй JlTIt-3T