Stimmen - 3, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Roland Dateigröße: 972.05 kb Dateiname: Unterrichtssprache:

Dieses Gerät hat auch andere Anweisungen:

Musikinstrumente - CUBE-20X (1.48 mb)

* Graduations for DELAY, REVERB on a panel are for reference. Be sure to check the sound as you adjust the effects. DELAY Turn the knob to change the time and amount of delay effects. REVERB Turn the knob to adjust the reverb level. 13.POWER SQUEEZER Switch The switch lights in red when the power squeezer function is on; the switch is unlit when the power squeezer is off. Switching on the Power Squeezer function allows you to reduce the amp’s output to 2 watts. Switching this on allows you to produce a sound that preserves the same tone and balance as when the amp is played at maximum volume, but at an output of 2 watts, for volume levels that are more suitable for the average home. * The Power Squeezer function affects only sounds input through the INPUT jack. It has no effect on sounds input via the AUX IN jack. 14.AUX IN Jack You can connect a CD player, MP3 player or other kind of device and have it play along with your guitar. This accepts a stereo miniature phone plug. However, the speaker and RECORDING OUT/PHONES output is monaural. * Determine the volume level by adjusting the volume control of the connected device. 15.FOOT SW (Footswitch) Jack You can use footswitches (optional BOSS FS-5U or FS-6) connected using a connection cable (optional Roland PCS-31) to switch channels (JC CLEAN/LEAD), and to turn EFX on and off. * When you connect only one footswitch by mono cable, you can only use it to switch channels (JC CLEAN/LEAD). SELECTEFX PCS-31 Polarity Switch whitered Panel descriptions Panel descriptions When Using Headphones Connect headphones to this jack. * No sound is played through the unit’s speaker while the RECORDING OUT/PHONES jack is in use. 17.POWER Switch This switches the power on and off. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. * If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 5). TUNING You can use “manual tuning,” whereby you switch to each individual string to tune it separately, and “chromatic tuning,” which automatically determines the closest pitch to that played by the string. Tuning in “Manual Mode” 1. Press the TUNER switch. 2. Use the Type switch to select the name of the string you want to tune, then play a single note on the open string. * No sound is played through the unit’s speaker while the tuner function is in use. Type Switch Position String Name 6E Open sixth string 5A Open fifth string 4D Open fourth string 3G Open third string 2B Open second string 1E Open first string * Reference Pitch: A4=440 Hz 3. Tune the string until the green indicator lights. * When the pitch is even lower, the indicator flashes. * When the pitch is even higher, the indicator flashes. Tuning in “Chromatic Mode” 1. Hold down the TUNER switch for at least one second so that the red indicator flashes. 2. Play a single note on the open string you want to tune. 3. Tune the string until the green indicator lights. 9 Connections Refer to the figure shown below to connect the CUBE-20X to other equipment. fig.01-02 Switching the Power On and Off Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 1. Make sure that all volume controls on the CUBE-20X and connected devices are set to 0. 2. Turn on all the devices connected to the CUBE-20X ’s input jacks (INPUT jack and AUX IN jack). 3. Turn on the CUBE-20X. 4. Switch on any equipment connected to the CUBE-20X’s RECORDING OUT/PHONES jack. 5. Adjust the volume levels for the devices. 6. Before switching off the power, lower the volume on each of the devices in your system and then TURN OFF the devices in the reverse order to which they were switched on. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. For protection from sudden big sound, always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on and off, but this is normal, and does not indicate a malfunction. 945 * If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 5). 921 * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * Before making the connections, be sure that the volume setting of the VOLUME knob for both amplifiers is set to “0.” 926...

Herunterladen

Geben Sie zwei Ziffern: