Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Use the following procedure to set the function of the foot switch. 1 Press [UTILITY]. The Utility Menu screen will appear. 2 Move the cursor to the SYSTEM icon and press [ENTER/YES]. 12 3 Move the cursor to FOOT Switch and select “PLAY/STOP” using the TIME/ VALUE dial. 4 Press [EXIT/NO] several times to return to the top screen. 5 Operate the foot switch. The song will alternate between play and stop each time you press the foot switch. 13 Adjusting the volume fig.07-09a 1 Move the MASTER fader up and down while the song is being played. The overall volume changes in response to the position of this fader. The display on the MIX level meter changes in response to the volume. 2 Move the Track faders for each track up and down. The volume of each track changes in response to the position of the corresponding fader. In addition, the display on each track’s level meter changes in response to its volume. 2 1 In certain cases, distortion will occur when a fader is raised too high. In particular, this occurs when the corresponding level meter rises beyond the 0 dB point. In such a case, lower the fader until the distortion is no longer present. 14 Changing the current position The current position within a song can be moved regardless of whether or not the song is being played. Any one of a number of different methods can be used to change the current position. Using the transport buttons The song position can be changed using the transport buttons located on the bottom left of the front panel. fig.07-09b 1 Press [ZERO]. Moves you to the time location 00:00:00-00.00. 2 Press [FF]. The current position will move forward by one second. 3 Press [REW]. The current position will move back by one second. 4 Hold down [STOP] and press [FF]. After the BR-1600CD has checked the V-Tracks currently selected for each track, the current position will jump to the point in the song at which the last recording was made. 5 Hold down [STOP] and press [REW]. After the BR-1600CD has checked the V-Tracks currently selected for each track, the current position will jump to the point in the song at which the first recording was made. • When the current position is changed, it takes a bit of time before you can carry out the next operation. This time is necessary for reading of data from the hard disk that will be needed for playback at the new song position. • It is not possible to change the current position while recording. 4 1 3 2 5 15 Changing the current position Using TIME/VALUE dial A cursor is displayed below the time for the current position on the top screen. Use the TIME/VALUE dial to change the time values and to move the current position. fig.07-09c 1 Move the cursor to the seconds, minutes or hours value. fig.07-101d 2 Turn the TIME/VALUE dial. The current position will change in units of seconds, minutes or hours. 3 Move the cursor to the measures or beats value. fig.07-103d 4 Turn the TIME/VALUE dial. The current position will change in units of measures or beats. “- - -” will be displayed after measure 999. 2,4 1,3 Hours Seconds Minutes Measures Beats 16 Changing the current position Using markers A number of song markers are set up in the demo songs in advance. These markers can be used to jump to the corresponding positions within the song. fig.07-09D 1 Press MARKER [SEARCH ]. The current position will jump to the location of one of the markers that has been set. Each time [SEARCH ] is pressed, the current position will jump forward to the next nearest marker. Note that the marker number corresponding to the current position is displayed at this time. 2 Press MARKER [SEARCH ]. The current position will jump back. Each time [SEARCH ] is pressed, the current position will jump back to the previous nearest marker. 3 Move the cursor to the value in the Marker box, and then use the TIME/ VALUE dial to specify a marker number. The current position will jump to the location of the corresponding marker. 1 2 • Up to 100 markers can be set up at will within a song. For more detailed information, refer to “Placing markers in your song (Marker)” (Owner’s Manual; p. 48). • The number of the marker at the current position is shown in the display’s Marker box. If no marker has been set up at this position, “- - -” is displayed. 17 Playing back repeatedly (Repeat Function) Use the Repeat function to play a certain section of the song in a repeated fashion. This function can also be combined with punch-in and punchout to carry out loop recording (Owner’s Manual; p. 45). fig.07-09f 1 Move to the song position from which looped playback is to be started. 2 Press [REPEAT]. [REPEAT] will start to flash and the current position will be specified as the start position (A) for repeat playback. 3 Move to the song position at which playback is to be looped back. 4 Press [REPEAT]. [REPEAT] will start to light up and the current position will be specified as the end position (B) for repeat playback. 5 To redo these settings, press [REPEAT] once ...