|
Anleitung Zusammenfassung
H HHF FF o oos ssc cci iil lll lla aat tti iio oon nn: :: This safety feature prevents from damages caused by frequencies above 20 kHz (feedback, etc.) by switching the power amp off. T TTe eem mmp ppe eer rra aat ttu uur rre ee: :: Should the temperature controlled fan cooler prove to be insufficient in extreme conditions, this circuit protects the output stage transistors from destruction by switching the device off. L LLi iim mmi iit tte eer rr: :: In order to protect the loudspeakers the combos CL and CCL are equipped with a limiter that limits the power amp outputs to 200 watts and 300 watts respectively. N NNo oot tte ee: :: One of the protective circuits is active when you find the MUTE LED is lit without having switched MUTE on. M MMU UUT TTE EE L LLE EED DD is continuously on even though you have not switched on MUTE. In case of a short-circuit please check the speaker cable. The amplifier must then be switched off and on again, to get back into playing mode after having removed the short-cir cuit. In any other situation the amplifier automatically switches back to playing mode as soon as it detects the fault has disappea red (e.g. the amplifier has overheated and cooled down again). GETTING STARTED 1. Make sure that loudspeakers capable of sustaining the load of a bass signal are connected to the S SSP PPE EEA AAK KKE EER RR O OOU UUT TT sockets, meaning the speaker unit should be linked to the S SSP PPE EEA AAK KKE EER RR O OOU UUT TT at the combos. 2. Make sure that the mains lead is connected and all external devices (effects) are properly connected and working. 3. Set the M MMA AAS SST TTE EER RR control to zero. 4. Plug your bass guitar into the amplifier's I IIN NNP PPU UUT TT with a shielded line-cable. 5. Press the P PPO OOW WWE EER RR switch to turn the device on. 6. Switch off M MMU UUT TTE EE - the red LED will turn off. 7. Switch the L LLI IIM MMI IIT TTE EER RR off (the 2-colored LED will turn off). E EEN NNG GGL LLI IIS SSH HH 8. Turn up all volume controls of your bass guitar. 9. Adjust the G GGA AAI IIN NN control until the clip LED flashes. 10. Set the M MMA AAS SST TTE EER RR control to your desired volume. 11. Use the sound controls / switches to adjust the sound as described in the respective chapters FRONT PANEL CONTROLS. 12. If necessary readjust G GGA AAI IIN NN. 13. Use the L LLI IIM MMI IIT TTE EER RR (LED green) to limit the preamp signal and fix its threshold (LED switches to red) using the GAIN control. 7 ENGLISH CL ND 4 FRONT PANEL CONTROLS INPUT socket to plug in a bass guitar. GAIN control + CLIP / LIMIT LED to adjust the input level. LIMITER switch + 2-colored CLIP / LIMIT LED to compress the signal within the preamp. LOW BOOST switch + LED to boost the low end. BASS control to boost / cut low frequencies. MID FREQ. control to determine the midrange frequency. MID LEVEL control to boost / cut the frequency adjusted with the MID FREQ. control. TREBLE control to boost / cut high frequencies. HIGH BOOST switch + LED to boost the highs. MUTE switch + ON / MUTE LED mutes the signal of all outputs except the PHONES and TUNER socket. To avoid switching noise use the MUTE switch only while no audio signal is being played back. MASTER control determines the main volume level. PHONES socket for connecting headphones (min 200 Ohm) REAR PANEL MAINS IN AC terminal with integrated fuse compartment for connecting the amplifier to mains. POWER switch for turning the amplifier on and off. GROUNDLIFT switch disconnects the protective ground line from signal ground. A humming loop may occur when several devices are hooked up to the same protective ground line and connected by line cables. Use GROUNDLIFT to eliminate humming loops. TUNER OUT to connect to a tuner, active when MUTE is enabled. LINE OUT socket allows connecting additional power amplifiers or active cabinets. EFF. LOOP for the insertion of an effects unit. Connect EFF. SEND with the input and EFF. RETURN with the output of the effects device. DI PRE / POST switch to route the signal to DI OUT socket PRE (pressed, direct signal from the bass) or POST (released, signal affected by equalizer or effects loop). Symmetric XLR out to connect to e.g. a mixing console. SUBSONIC switch to cut low frequencies...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - CCL 210 ND 8 (978.93 kb)
Musikinstrumente - CCL ND 8 (978.93 kb)
Musikinstrumente - CL ND 4 (978.93 kb)