Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Setting Modulation Speed and Delay Time Using the Pedals Pedal 1 2–4 1 Indicators Effect TYPE value MODULATION HARMONIST OCTAVE DELAY MOMENTARY TAP PHRASE LOOP E-15 Convenient Functions English Deutsch Francais Italiano Espanol Portugues Nederlands You can record up to 38 seconds of a performance and play back the recorded section over and over. You can also layer additional performances with the recording as it plays back (overdubbing). This lets you create realtime backing performances on the fly. This section describes how to carry out the operation when in Manual mode. When you're in Memory mode, you can accomplish the same operation by using the number pedal for the currently selected patch. 1. Set the DELAY effect's TYPE knob to PHRASE LOOP. The unit goes into recording standby and the pedal's indicator flashes at a fixed interval. 2. Press the DELAY pedal. Recording starts as soon as you press the DELAY pedal, and the pedal’s indicator flashes rapidly. 3. Press the DELAY pedal again. Recording ends. As soon as recording stops, repeated playback of what's been recorded starts, and the pedal's indicator lights continuously. An oscillating sound may be audible with extremely short recording times. 4. To layer additional recordings (overdubbing), repeat Steps 2 and 3. When you switch the DELAY effect's TYPE knob to another position or turn the power off, the recorded data is deleted. 5. Adjust the phrase loop's volume as desired with the DELAY effect's E. LEVEL knob. 6. Press the pedal twice switch to stop the playback. The unit returns to recording standby. .. Press the DELAY pedal twice within the span of one second. .. When playback ends, the recorded data is deleted. Phrase Loop Play Pedal 1 2,3,6 5 Indicators OVERDUB PLAY STANDBY REC 1. 2. 3. 4. 6. 6. 4. Lit Dark Pedal Indicator When you call up patches or EZ Tones, an effect's parameters may not reflect the actual position of the control knobs. You can set how the parameters behave when the control knobs are moved in this state. 1. Press number pedals 3 and 4 at the same time to change to Manual mode (p. E-10). 2. Hold down [EDIT/EXIT] and press the COMP pedal. 3. Use NS THRES/BANK [ ] or [ ] to select the method of control operation. 4. Press [WRITE]. The setting is stored in memory. Making the Settings for Control Operation 2 1 4 3 Display Control operation n0 The value changes immediately as the knob is turned (factory setting). n1 The value changes once the knob is turned past the position corresponding to the currently set value. E-16 Restoring the Factory Settings (Factory Reset) You can restore the settings in the ME-70 (User patch, tuner reference pitch, and knob response method (p. E-15)) to the values set when the unit was shipped from the factory. 1. Press number pedals 3 and 4 at the same time to switch to Manual mode (p. E-10). 2. Hold down [EDIT/EXIT] press MOD Pedal. “F” appears in the display. 3. Press [WRITE]. The Tuning Guide flashes. 4. Press [WRITE] again. The display flashes and the factory reset is executed. Never turn off the power while Factory Reset is in progress. 3, 4 2 1 Adjusting the Expression Pedal The ME-70's expression pedal has been set for optimal operation at the factory. However, extended use and certain operating environments can result in the pedal going out of adjustment. If you encounter problems such as the expression pedal's ON/OFF switch not functioning or the volume pedal not fully cutting off the sound, you can use the following procedure to readjust the pedal. When operating the expression pedal, be careful not to get your fingers pinched between the movable part and the panel. In places with small children, an adult should provide supervision and guidance until the child is capable of following all the rules essential for the safe operation of the unit. 1. Press number pedals 3 and 4 at the same time to switch to Manual mode (p. E-10). 2. Hold down [EDIT/EXIT] press DELAY Pedal. The display shows “Pd,” then “Up.” 3. Move the heel of the expression pedal all the way down, then release the pedal and press [WRITE]. The display shows “dn.” 4. Move the toe of the expression pedal all the way down, then release the pedal and press [WRITE]. A value indicating the current stiffness (sensitivity) of the expression pedal switch appears in the display. If the display flashes in Steps 3 or 4, press the pedal again, and then press [WRITE]. 5. Use NS THRES/BANK [ ] and [ ] to adjust the stiffness (sensitivity) of the expression pedal switch. The lower the value, the more easily the switch will respond, even when pressed lightly. This is set to “5” when shipped from the factory. 6. Press [WRITE]. The setting is saved in memory. 5 3 3,4,6 4 1 2 Appendices Preset Patch List Patch Number Explanation PU 1-1 Rough distortion sound, good for backing. S/H 1-2 Well sustained distortion sound, good for solos. S/H 1-3 Crunch sound suitable for blues. S/H 1-4 Clean sound for arpeggio. S/H 2-1 Metal sound good for riffs. H 2-2 ...
Dieses Handbuch ist für folgende Modelle:Musikinstrumente - G6037008-01 (5.09 mb)