Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Sanyo Dateigröße: 1.43 mb Dateiname: Unterrichtssprache:

The POWER indicator will light RED and the READY indicator will light GREEN. Press the POWER (LAMP) ON/OFF button on the projector or on the remote control unit to ON. The POWER indicator will light dim and the cooling fan will operate. The wait display (A MOMENT!/UN MOMENTO! and numeral 30) appears on the screen and the count-down starts (30-29-28-,..1). The signal from the video source appears after 30 seconds. CAUTION: • THIS PROJECTOR USES A METAL-HALIDE ARC LAMP. IF YOU TURN ON THE LAMP, DO NOT TURN IT OFF FOR AT LEAST 5 MINUTES SO THAT ITS LIFE WILL NOT GET SHORTER. • DO NOT UNPLUG THE PROJECTOR OR TURN THE MAINS ON/OFF SWITCH (LOCATED ON THE BACK OF THE PROJECTOR) TO OFF UNTIL THE COOLING FAN HAS STOPPED OPERATING. NOTE 1: After you turn off the projector using the POWER (LAMP) ON/OFF button on the projector (or on the remote control unit) you must wait one minute before you can turn the projector on again. NOTE 2: TEMPERATURE WARNING INDICATOR flashes red, the projector will automatically turn off. Wait at least 5 minutes before turning the projector on. If the TEMPERATURE WARNING INDICATOR continues to flash, follow the procedures below: (1). Press POWER (LAMP) ON/OFF button to OFF. (2). Check the air filter for dust accumulation. (3). Remove dust with vacuum cleaner (See air filter care and cleaning on page 23.) (4). Press POWER (LAMP) ON/OFF button to ON. If the TEMPERATURE WARNING INDICATOR still continues to flash, call your authorized distributor or dealer for service. TO TURN OFF THE PROJECTOR Press the POWER (LAMP) ON/OFF button on the projector or on the remote control unit. The ”(1) POWER OFF ?” appears on the screen. Press again the POWER (LAMP) ON/OFF button to OFF the projector. The POWER indicator will light bright and READY indicator will turn off. The cooling fan will operate for 1 minute after the projector is turned off. (During this ’’cooling down” period, the projector can not be turned on.) After 1 minute, the READY indicator will light green again and the projector may be turned on by pressing the POWER (LAMP) ON/OFF button. (!) POWER OFF ? A MOMENTÎ/UN MOMENTO! 0 30 ADJUST THE PROJECTOR VIDEO MODE SELECT Press the MODE button (located on projector or remote control unit) to select Computer Input, Video Input-1 or Video Input-2. The ’’COMPUTER”, ”AV1” or ”AV2” display will appear on the screen. Press the ALTER button on the remote control unit to alternate quickly between the two modes. (Current mode and Previous mode) For example, Computer IN/OUT Terminals and AV1 are connected with personal computer and VCR respectively. Firstly project computer image on the screen. Secondly press MODE button to select AV1. And then, press ALTER button to select previous mode (Computer mode). CURRENT MODE PREVIOUS MODE AV1 MODE -► COMPUTER MODE COMPUTER MODE -► AV2 MODE AV2 MODE -► AV1 MODE VOLUME ADJUSTMENT Press VOLUME buttons (located on projector or remote control unit) to adjust the volume. The screen display will appear. Pressing (+) will increase volume and the green indicator will increase to the right on the screen. Pressing (- ) will decrease volume and the green indicator will decrease to the left on the screen. SOUND MUTE ADJUSTMENT Pressing SOUND MUTE button on the remote control unit will mute audio. Press SOUND MUTE button again to restore audio to its previous level. ZOOM ADJUSTMENT (Without remote control unit) Press ZOOM/FOCUS button until zoom display appears on the screen, and press LEVEL (+) or (-) to obtain your desired picture size. (The zoom display will appear for 5 seconds.) For a larger picture, press (+) and for a smaller picture, press (-). ZOOM ADJUSTMENT (With remote control unit) Press ZOOM ( a ) or ( v ) to obtain your desired picture size. (The zoom display will appear for 5 seconds.) For a larger picture, press ( a ) and for a smaller picture, press ( v ). FOCUS ADJUSTMENT (Without remote control unit) Press ZOOM/FOCUS button until focus display appears on the screen, and press LEVEL (+) or ( - ) for sharper, crisper picture. (The focus display will appear for 5 seconds.) FOCUS ADJUSTMENT (With remote control unit) Press FOCUS ( ) or ( . ) for sharper, crisper picture. (The focus display will appear for 5 seconds.) PICTURE ADJUSTMENT The normal picture level is factory preset on the projector and can be obtained anytime by pressing the NORMAL button on the projector, or on the remote control unit. (The Normal display will appear for 5 seconds.) Picture adjustments can be made by using the MENU and LEVEL buttons on the projector, or on the remote control unit. (See picture adjustment on page 21-22.) FOCUS NORMAL ZOOM ÖK'MUTE 11111111 ^ SOUND IIIIIIII - SYSTEM SELECT • COMPUTER MODE When a computer is connected to the projector and both of the computer and the projector are turned On, the type of the connected computer system appears on the screen. (See ’’ON-SCREEN DISPLAY” on page 27.) If any of the...

Herunterladen

Geben Sie zwei Ziffern: