Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Check all input and tion. Shorted cable. output connections for s e c u re fit. Isolate and re p l a c e the damaged cable. Pro g ram volume canOt be Amplifier or outboard gear Connect amplifier or outboard adjusted with master vo l u m e connected to the re c o rd out-gear to master output. c o n t ro l . put. No powe r. I m p roperly connected AC cord Properly connect AC cord to or power line source not on AC power source. Turn powe r o n . The amplifier is turned up, Faulty output connections but there is no signal. Improper level adjustment. No signal in headphones. Improper connection. Improper level or cue mix settings. Properly connect amplifier, or outboard gear to mixer. Properly set crossfader, channel faders, gain controls, and input selector tog gles. Check headphone connection to mixer. Tighten if necessary. Adjust headphone level and cue mix to the proper level and channel settings. D E S C R I P T IO N O F FU N C TI O N S D E S C R I P T IO N O F FU N C TI O N S 1. Input selector switches: Selects phono or line inputs of channels 1 and 2 2. Gain control: Controls the input sensitivity of channels 1 and 2 3. Equalizer: Individual controls for low frequency, midrange, and high frequency equalization with (+9/-26 dB) Any changes made to EQ settings will change the overall output level. 4. Channel faders: Control the output level of channels 1 and 2 5. Crossfader: Fades the master output between channels 1 and 2 6. Level meter: Based upon the meter mode selector (7) setting, the level meter displays the master output stereo signal level, or the cue levels of channels 1 and 2 7. Meter mode selector: Determines the setting of the level meter (6). When pressed, cue levels of channels 1 and 2 are displayed. When released, stereo master output signal is displayed. 8. Power switch: Selects power "ON" or "OFF" 9. Fader Start controls: Activate the Fader Start function when connected to a CD player with fader start capabilities (such as the Next! NCD-7000). When fader start is engaged, the CD player can be started and paused by the crossfader. This function is defeated while crossfader is reversed. 10. Master level control: Controls the overall signal output level of the Master output 11. Booth level control: Controls the overall signal output level of the Booth output 12. Cue level control: Controls the overall headphone output level. 13. Cue select: 3 position selector switch dtermines what is heard in the headphones, channel 1, 2, or master output 14. Headphone output: Connection for 1/4 inch headphone. Recommended headphone impedance is 32-200 ohms for maximum volume 15. Mic EQ: Individual controls for low and high frequencies equalization with (+/-12 dB) Any changes made to EQ settings will change the overall microphone output level. 16. Mic volume control: Controls the overall mirophone output level 17. Crossfader Reverse: Reverses the direction of the crossfader. The fader start function is defeated while crossfader is reversed. 18. Microphone input: 1/4O connector 19. Ground connector: Connects to the turntable ground connector to eliminate electrical hum. Ground connectors are usually supplied with turntables 20. Phono/CD inputs: Switchable line / phono signal inputs for channels 1 and 2 21. Line inputs: Line signal inputs for channels 1 and 2 22. Phono/CD selector switches: Switches CD/Phono inputs for channels 1 and 2 between line and phono 23. Fader Start output: Connects to the fader start inputs of CD players with fader start function such as the Next! NCD-7000 24. Booth output: Auxiliary output, usually for DJ booth monitoring. Level is controlled by booth level control (11) 25. Master output: Level is controlled by master level control (10) 26. REC output: Record out connects to tape recorder, mini disk recorder, etc. to record performance 27. Voltage selector: Selects between 115V (US) / 230V (EU) 28. Power cord connector: Input connection for the supplied removable power cord. TE C H N I CA L S P E C I FI C AT I O N S C RO S S FA D E R C LE A N I N G TE C H N I CA L S P E C I FI C AT I O N S C RO S S FA D E R C LE A N I N G The PRO-30 crossfader may need lubrication from time to time. This will extend Line inputs: 2 (RCA), 150 mV / 47K ohm the fader life and eliminate any potential damage due to extended heavy usage. Phono inputs: 2 (RCA), 3 mV / 47K ohm Cleaning Instructions DJ mic input: Master output: 1 (1/4 inch), 1.6 mV / 600 ohm 1 (RCA), 1V / 600 ohm 1. Remove the crossfader by unscrewing the 2 outer screws (removing the 2 inner screws will detach the fader from the fader plate) and disconnecting the cable from the mixer. Record output: Headphone output: Frequency Response: 1 (RCA), 350 mV / 600 ohm 1 (1/4 inch), 32 -200 ohms recommended 20 Hz -20 kHz, +/- 0.5 dB Tone Control : + 9/-26 dB (Hi, Mid, Low) 2. Spray a small amount of cleaner or lubricant into both ends of the fader and slide the fader back and forth a few times to spread the fluid evenly throughout the fader. Mic Tone...